recreation sites with only one riser must comply with the requirements for toilet room size and clearances in section 603 of ABAAS and with the requirements for toilet seats, grab bars, controls...
Search Results "Control End Wall"
Commonly Searched Documents
-
Toilet Buildings and Pit Toilets
-
§ 37.131(a)(1)(i)
The corridor shall include an area with a three-fourths of a mile radius at the ends of each fixed route....
- Bobrick Reversible Folding Shower Seat B-5181
-
E2-a
[ADA Standards § 4.4.1] Yes No Note: These objects may be wall mounted or free standing....
- Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables Using Recycled Plastic
- Pilot Rock APTX Full Sized Pedestal Rectangular Utility Table Using Lumber
-
11B-609.4 Position of grab bars
The height of the lower grab bar on the back wall of a bathtub shall comply with Section 11B-607.4.1.1 or 11B-607.4.2.1....
-
Height from Finish Floor or Ground: ADA Standard Section 703.5.6
EXCEPTION: Visual characters indicating elevator car controls shall not be required to comply with 703.5.6....
-
II. Systemic Considerations
Training criminal justice personnel, conducting reviews of policies and procedures, and collaborating with mental health and disability services providers are three ways to achieve that end...
-
Technical Memorandum TM 2013-23 Storage (Not in Kitchens or Kitchenettes)
For purposes of compliance with TAS 225.2, the Department shall consider base and wall cabinets to be the same type of storage if designed the same (i.e. both have doors), used for the same...
-
The Presentation Area / Speaker’s Platform Design and Considerations
Neither should a presenter using a mobility device be seated at the end of a skirted table instead of with the other presenters....
-
604.8.1.2 Doors
Doors shall be located in the front partition or in the side wall or partition farthest from the water closet....
-
604.8.1.2 Doors
Doors shall be located in the front partition or in the side wall or partition farthest from the water closet....
-
Signage
Where permanent identification is provided for rooms and spaces, signs shall be installed on the wall adjacent to the latch side of the door....
-
Minimum Number: ADA Standard Section 234.3
Section 234.3 covers scoping requirements in the current ADA Standards for the minimum number of wheelchair spaces required at amusement rides.
-
11B-411.2.1.1 Location
Hall call consoles shall be wall-mounted. On floors with a building entry, including parking and transfer levels, each hoistway entrance shall be adjacent to a hall call console....
-
11B-411.2.1.1 Location
Hall call consoles shall be wall-mounted. On floors with a building entry, including parking and transfer levels, each hoistway entrance shall be adjacent to a hall call console....
-
11B-411.2.1.1 Location
Hall call consoles shall be wall-mounted. On floors with a building entry, including parking and transfer levels, each hoistway entrance shall be adjacent to a hall call console....
-
11B-809.10.7.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from a wall or partition that is 54 inches (1372 mm) minimum in length....
-
Dimensions: ADA Standard Section 810.2.2
Board’s Note to Reader: The Department of Transportation’s ADA standards indicate that compliance is required to the extent construction specifications are within a public entity's control...
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
8.1 Excluded Populations Needing Future Attention
In support, various Committee members cited reports from the Centers for Disease Control and Prevention (CDC), which tabulates data on obesity among individuals within states and nationwide...
-
Sloped Surfaces
Rest one end of the level at the highest point of the sloped surface and lift the other end (see image) until the bubble is in the middle of the tube. This is the "level" position....