EXCEPTION: The sloping portions of handrails serving stairs and ramps shall not be required to comply with 307.3. Figure 307.3 Post-Mounted Protruding Objects...
Search Results "Handrail Clearance"
-
307.3 Post-Mounted Objects
-
DIVISION 5: GENERAL SITE AND BUILDING ELEMENTS
11B-502 Parking Spaces 11B-503 Passenger Drop-Off and Loading Zones 11B-504 Stairways 11B-505 Handrails...
-
Landings [4.8.4]
Handrail extensions can wrap around landings. It is recommended that landings of exterior ramps be drained so that water does not accumulate on the surface....
-
11B-405.9 Edge protection
Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with Section 11B-406.2.2. 2....
-
11B-405.9 Edge protection
Exceptions: Edge protection shall not be required on ramps that are not required to have handrails and have sides complying with Section 11B-406.2.2....
-
Re: 404.2.6 Doors in Series and Gates in Series
To summarize my opinion, you need compliant door maneuvering clearance at each door, AND space to avoid fighting two doors at once....
-
Murdock Manufacturing Grab Bars
Grab bar is 1-1/2 inch (3.81 cm) diameter satin finish stainless steel and have 1-1/2 inch (3.81 cm) clearance to wall....
-
704.5 TTY Shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
4.2.6* SIDE REACH
If the side reach is over an obstruction, the reach and clearances shall be as shown in Fig. 6(c). Figure 6 Side Reach...
-
Clear Floor Space [§309.2]
Clear Floor Space Additional clearance is required if the space is obstructed on three sides for more than half the depth to allow easier maneuvering into the space....
-
11B-608.2.3 Alternate roll-in type shower compartments
FIGURE 11B-608.2.3 ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE...
-
1009.4.1 Clear Deck Space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
Clear Floor Space [§309.2]
If clear floor space is obstructed on both sides more than half the minimum required depth, a wider clearance (36” min.) is required for maneuvering and sway....
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
§ 38.125(a)(1) General
., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a seating location...
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars....
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
410.1 General
Because an accessible route requires an 80 inch (2030 mm) vertical clearance, care should be taken in selecting lifts as they may not be equally suitable for use by people using wheelchairs...
-
T503 Passenger Access Routes
In the 2016 Non-Rail Vehicle Guidelines, passenger access routes (which were referred to as “accessible circulation paths” in the proposed rule) must provide clearances sufficient to permit...
-
Furnishings and Equipment
In addition, placement of non-fixed elements can affect the accessibility of an area by encroaching into accessible routes and clearances....
-
11B-608.2.1 Transfer type shower compartments
Clearance of 36 inches (914 mm) wide minimum by 48 inches (1219 mm) long minimum measured from the control wall shall be provided....
