Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
Search Results "Vertical Clearance"
-
11B-404.2.10 Door and gate surfaces
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
223.1 General
Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1 require vertical access to all levels of facilities....
-
(C) NYCT’s interpretation of the ADA and DOT’s implementing regulations is too narrow.
To address another argument presented by NYCT,1 the ADA Accessibility Guidelines (ADAAG) do not, as NYCT contends, limit the requirement that “a means of accessible vertical access” be provided...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
-
Don-Jo Mfg., Inc. Pull Plate 7011
Number 7011 Dimensions 3-1/2" x 15" Ansi J405 Ctc 5-1/2" Diameter 5/8" Projection 2" Clearance...
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
4.2.5* Forward Reach
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b)....
-
4.34.5.3 LAVATORY, MIRRORS, AND MEDICINE CABINETS
(2) If a cabinet is provided under the lavatory in adaptable bathrooms, then it shall be removable to provide the clearances specified in 4.22.6....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
ASME
Lifts are classified as: vertical platform lifts, inclined platform lifts, inclined stairway chairlifts, private residence vertical platform lifts, private residence inclined platform lifts...
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
1.17 Unobstructed view
purposes of this Consent Order, shall mean and refer to a view to the screen that is not blocked or interfered with by any seats, railings, or other objects and is configured to have visual clearance...
-
7. Lavatory
Is the lavatory (wash basin) in each accessible guestroom bathroom no more than 34" high with at least 29" high clearance under the front edge to allow persons who use wheelchairs to pull...
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2½ inches (64 mm) minimum measured along the vertical centerline of the element....
-
Gaps
spaces are provided on amusement rides, the floors of rides must be coordinated with the floors of the load and unload areas so that when the ride is at the load and unload position, the vertical...
-
Adjustable height protocol
The amount of vertical distance that the seat was raised/lowered each time depended on the subject’s perceived and observed transfer abilities....
