They include information on space required for “kneeholes,” reaching abilities of wheeled mobility users, clear floor area space requirements and maneuvering clearances....
Search Results "Vertical Clearance"
Commonly Searched Documents
-
BS8300:2001 Research
-
2.2.6 Door Use
2 lbf. (9 N) < 2 lbf. (9 N) 7 to 8 lbf. (31 to 36 N) Threshold 3 mm 0 6 mm Latch Yes Yes Yes Push side clearance...
- Pilot Rock CN-TR-52 Tilting Trash Receptacle
-
803 Dressing, Fitting, and Locker Rooms
In the proposed rule, an exception to this provision noted that a portion of this space (6 inches maximum) could extend under partitions or openings without doors that provide toe clearance...
-
805 Medical Care and Long-Term Care Facilities
Commenters opposed this requirement, noting that it is inconsistent with specifications for wheelchair turning space in section 304 which recognize knee and toe clearances for specified...
-
Wheelchair Turning Space [4.2.3]
Overlapping Fixed Elements Fixed elements can overlap turning space if required knee and toe clearances are provided....
-
III-4.4300 Standards to apply
However, because of space constraints, he is unable to widen the door to the full 32-inch clearance required for alterations under ADAAG....
-
608.2.2 Standard Roll-In Type Shower Compartments
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Note: inside finished dimensions measured at the center points of opposing sides Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance...
-
1009.4.1 Clear Deck Space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars. Figure 1009.4.1 Clear Deck Space at Transfer Walls...
-
E2-c
Are any interior stairs along these routes configured with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch high head clearance so that...
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars. FIGURE 11B-1009.4.1 CLEAR DECK SPACE AT TRANSFER WALLS...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
Kitchens, Kitchenettes, or Wet Bars [9.2.2(7)]
A forward approach to sinks (with knee and toe clearances below) is recommended for sinks that may be used more regularly or for extended periods of time, such as a kitchen in apartment-style...
-
304.3.2 T-Shaped Space
The space shall be permitted to include knee and toe clearance complying with 306 only at the end of either the base or one arm....
-
Width [4.3.3.] and Passing Space [4.3.4]
However, the minimum width of hallways and corridors is often further determined by ADAAG requirements for clear floor space at elements such as drinking fountains, door maneuvering clearances...
- Bobrick TrimLineSeries ADA Surface-Mounted Hand Dryer B-7128.230V
- Bobrick ClassicSeries Surface-Mounted Soap Dispenser B-2111
-
1007.8 Exterior area for assisted rescue
This construction shall extend vertically from the ground to a point 10 feet (3048 mm) above the floor level of the area for assisted rescue or to the roof line, whichever is lower....
-
1003.2.13.7 Exterior area for assisted rescue
This construction shall extend vertically from the ground to a point 10 feet (3048 mm) above the floor level of the area for assisted rescue or to the roof line, whichever is lower....
-
A4.30.4 Raised and Brailled Characters and Pictorial Symbol Signs (Pictograms)
Vertical separation between cells .395 in....
-
Accessible Routes within a Building or Facility
Accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility....
-
[F] 907.4.2.2 Height
The height of the manual fire alarm boxes shall be not less than 42 inches (1067 mm) and not more than 48 inches (1219 mm) measured vertically, from the floor level to the highest point...
-
11B-303.3 Beveled
A change in level of 1/2 inch (13 mm) is permitted to be 1/4 inch (6.4 mm) vertical plus 1/4 inch (6.4 mm) beveled....