and communication system receptacles shall comply with Section 11B-308 except the low reach shall be measured to the bottom of the outlet box and the high reach shall be measured to the top...
Search Results "Curb Ramp Top Landing"
-
11B-308.1.2 Electrical receptacle outlets
-
Dimensions: ADA Standard Section 810.2.2
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
2. Electronic (Digital) Level
The slope of a curb ramp or a walkway can make or break its accessibility....
-
11B-809.10.8.7 Mirrors and towel bars
Where towel bars are provided they shall be installed 40 inches (1016 mm) maximum above the finish floor to the top of the bar....
-
11B-809.10.8.7 Mirrors and towel bars
Where towel bars are provided they shall be installed 40 inches (1016 mm) maximum above the finish floor to the top of the bar....
-
11B-221.4 Designated aisle seats
For example, an assembly area has two aisles (A and B) serving seating areas with an accessible route connecting to the top and bottom of Aisle A only....
-
11B-606.3 Height
ETA Editor's Note Top-mounted sinks installed in counters having the top surface 34 inches above the floor will exceed the maximum rim height allowed, regardless of how thin the flange...
-
11B-221.4 Designated aisle seats
For example, an assembly area has two aisles (A and B) serving seating areas with an accessible route connecting to the top and bottom of Aisle A only....
-
11B-606.3 Height
ETA Editor's Note Top-mounted sinks installed in counters having the top surface 34 inches above the floor will exceed the maximum rim height allowed, regardless of how thin the flange...
-
11B-308.3.2 Obstructed high reach
The top of washing machines and clothes dryers shall be permitted to be 36 inches (914 mm) maximum above the finish floor. 2. ...
-
Symmetry Vertical Platform Lift VPC-EL
Nonskid platform surface Obstruction safety panel under platform (when not installed within a runway enclosure) Alarm and emergency stop switch Grab rail Landing...
-
11B-804.2.2 U-Shaped
In U-shaped kitchens enclosed on three contiguous sides, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 60 inches (1524...
-
11B-804.2.2 U-Shaped
In U-shaped kitchens enclosed on three contiguous sides, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 60 inches (1524...
-
Turning Space: ADA Standard Section 808.2
Where provided, areas that are raised or depressed and accessed by ramps or platform lifts with entry ramps shall provide unobstructed turning space complying with 304....
-
Barriers: ADA Standard Section 1006.3.2
Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings 60 inches (1525 mm) wide minimum shall be provided at intervals not to exceed 75 yards (69 m...
-
11B-1006.3.2 Barriers
Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings 60 inches (1524 mm) wide minimum shall be provided at intervals not to exceed 75 yards (69 m...
-
11B-1006.3.2 Barriers
Where curbs or other constructed barriers prevent golf cars from entering a fairway, openings 60 inches (1524 mm) wide minimum shall be provided at intervals not to exceed 75 yards (69 m...
-
1009.3.2 Submerged Depth
Where landings are required by 405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level....
-
R302.7.2 Vertical Surface Discontinuities
However, objects such as utility covers, vault frames, and gratings should not be located on curb ramp runs, blended transitions, turning spaces, or gutter areas within the pedestrian access...
-
Specific Spaces and Occupancies
provisions (noted with an asterisk) and also set forth additional requirements for spaces and facilities provided in housing at a place of education, social service center establishments, and curb...
-
Allowances for Typical Roadway Geometry
The draft guidelines also permitted the cross slope of pedestrian access routes within midblock pedestrian street crossings and of curb ramps at midblock pedestrian street crossings to equal...
-
11B-1009.3.2 Submerged depth
Where landings are required by Section 11B-405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (762 mm) maximum below the stationary water level....
-
11B-1009.3.2 Submerged depth
Where landings are required by Section 11B-405.7, at least one landing shall be located 24 inches (610 mm) minimum and 30 inches (762 mm) maximum below the stationary water level....
-
Single Occupant Structures: ADA Standard Section 203.6
Section 203.6 covers scoping requirements of general exceptions for single occupant structures in the most current ADA Standards.
