The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
Search Results "Curb Ramp Surface"
- Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
-
Seat Width Evaluation
many participants (the 25th through 95th percentiles) for their level, highest and lowest height transfer regardless of the presence or absence of grab bars or a backrest on the transfer surfaces...
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
-
Bus Loading Zones: ADA Standard Section 209.2.2
Section 209.2.2 covers scoping requirements in the current ADA Standards for bus loading zones.
- Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
-
Entrance Landings
Entrance landings must accommodate door maneuvering clearances as well as landings for provided ramps. Entrance Landing...
-
11B-209.2.2 Bus loading zones
In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply...
-
11B-209.2.2 Bus loading zones
In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply...
-
Shower Compartments
• The 1991 Standards and the 2010 Standards permit a ½-inch maximum curb in transfer-type showers....
-
406.3 Sides of Curb Ramps
406.3 Sides of Curb Ramps. Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
-
§ 38.25(b) Contrast
All step edges, thresholds and the boarding edge of ramps or lift platforms shall have a band of color(s) running the full width of the step or edge which contrasts from the step tread and...
- Access Board: Accessible Route Carpet
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible. ...
-
Elevated Accessible Routes
Two common methods for providing access to elevated play components are ramps and transfer systems....
-
T402.3 Installation and Operation
When used for boarding and alighting, ramps and bridgeplates shall be firmly attached to the non-rail vehicle to prevent displacement....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
C1-6. Accessible Route Slope
If the slope of part of the accessible route is greater than 1:20, does this part meet the following requirements for an accessible ramp? Yes _____ No _____...
-
Can stair treads and risers be perforated?
Stair treads must meet requirements for floor or ground surfaces which specify that surface openings not allow passage of a sphere more than ½ inch in diameter (§302.3)....
-
Gangway Slope and Rise Exceptions
For example, where the vertical distance between where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level is 4 feet, the gangway...
- Landscape Forms Inc. Morrison Table and Stool Collection Video
- Landscape Forms Inc. Olithas Outdoor Tables and Benches Video
-
Clear Floor or Ground Space: ADA Standard Section 902.4.1
A clear floor space complying with 305 positioned for forward approach shall be provided. Knee and toe clearance complying with 306 shall be provided, except that knee clearance 24...
