Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
Search Results "Elongated Water Closet Seat"
Filters
Commonly Searched Documents
-
Height – M301.2.1 & M302.2.1
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
Toilet and Bathing Facilities: ADA Standard Section 806.2.4
No fewer than one water closet, one lavatory, and one bathtub or shower shall comply with applicable requirements of 603 through 610....
-
1134A.6, Item 1.2
A water closet may project a maximum of 12 inches (305 mm) into the opening, provided that a minimum of 36 inches (914 mm) clear space is maintained between the water closet and the shower...
-
§ 36.302(f)(4) Notification of accessible seating locations
(4) Notification of accessible seating locations. ...
-
APPENDIX E - SEATING PLANS FOR MODIFIED THEATERS
APPENDIX E SEATING PLANS FOR MODIFIED THEATERS...
-
Hot water heaters and knee clearance
If the hot water has sharp or abrasive edges or if the piping serving the hot water heater falls within the required knee clearance.............
-
Team or player seating areas. (Section-by-Section Analysis)
Section 221.2.1.4 of the 2004 ADAAG requires one or more wheelchair spaces to be provided in each team or player seating area with fixed seats, depending upon the number of seats provided...
-
Types of Alternative Designs
Respondents reported the following types of design alternatives: Water Closet: The water closet was moved further away from the sidewall (> 18+" from the sidewall to the centerline...
-
San Jamar C3165FBL Medium Pull-Type Water Cup Dispenser
Our Medium Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
San Jamar C3165WH Medium Pull-Type Water Cup Dispenser
Our Medium Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
San Jamar C3165TBL Medium Pull-Type Water Cup Dispenser
Our Medium Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis)
Section 36.308(a)(1)(ii)(A) and (B) have been revised to provide that wheelchair and companion seats must be an integral part of the seating area, dispersed to all accessible seating levels...
-
Error/Omission: Toilet rooms with 6 or more toilet stalls lack a 36" wide "ambulatory" toilet stall.
Requirement: 4.22.4, 4.23.4 Water Closets....
-
M305.2.1 Location (Section-by-Section Analysis)
patients in the supine, prone, or side-lying position with end transfer surfaces, M301.2.3.1 in the final rule, and all diagnostic equipment with transfer surfaces used by patients in the seated...
-
San Jamar C4150SS Small Pull-Type Water Cup Dispenser
Our Small Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
San Jamar C4160WH Small Pull-Type Water Cup Dispenser
Our Small Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
San Jamar C4160TBL Small Pull-Type Water Cup Dispenser
Our Small Pull–Type Water Cup Dispensers are designed with smart features and available in attractive colors and finishes to fit any application....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.3 Height (Section-by-Section Analysis)
In the MDE NPRM there was no specific requirement regarding the height of the transfer support, only that it be “within reach” of the patient (proposed M305.2.1). The Access Board...
