The profiles are made using high tensile 6063-T5 aluminum extrusions for superior strength....
Search Results "High Speed Rail"
-
Panda S.85 All Aluminum Slim Profile Lift and Slide System
-
Inpro Corporation IPC® HR9 Northern Hardwoods® Real Wood Handrail
Benefits Design interior environmentswith a number of stain colors or unfinished poplar Coated with a low-VOC UV-protective clear finish Coordinate with Northern Hardwoods chair rails...
-
1008.2 Accessible Routes
Where accessible routes serve ground level play components, the vertical clearance shall be 80 inches high (2030 mm) minimum....
-
§382.51(a)(6)
The captioning must be high-contrast insofar as is feasible....
-
7. Grab Bars
Are there two horizontal grab bars (one high/one low) along the side of the tub that are at least 24" long for stabilization and aid in transfer from a wheelchair to the fixed tub seat -...
-
4.35.5 Mirror
Where mirrors are provided in dressing rooms of the same use, then in an accessible dressing room, a full-length mirror, measuring at least 18 in wide by 54 in high (460 mm by 1370 mm),...
-
R406.2 Unobstructed Forward Reach
Where a forward reach is unobstructed, the high forward reach shall be 1220 mm (4.0 ft) maximum and the low forward reach shall be 380 mm (1.25 ft) minimum above the finish surface....
-
M303.2.6 Edge Protection
Where wheelchair spaces are provided on a platform raised more than 1 ½ inches (38 mm) in height, edge protection 2 inches (51 mm) high minimum measured from the surface of the platform...
-
407.2.3.2 Car Designations
Tactile characters shall be 2 inches (51 mm) high minimum....
-
1008.2 Accessible Routes
Where accessible routes serve ground level play components, the vertical clearance shall be 80 inches high (2030 mm) minimum....
-
4.26.2* SIZE AND SPACING OF GRAB BARS AND HANDRAILS
Handrails may be located in a recess if the recess is a maximum of 3 in (75 mm) deep and extends at least 18 in (455 mm) above the top of the rail (see Fig. 39(d))....
-
§ 38.83(a)(1) General
All new light rail vehicles, other than level entry vehicles, covered by this subpart shall provide a level-change mechanism or boarding device (e.g., lift, ramp or bridge plate) complying...
-
B. Restrooms
These specifications are derived from requirements for rail vehicles and represent compromises between space needed for use and constraints imposed by vehicle dimensions....
-
III. Handrails and Stanchions
Handrails and Stanchions In addition to the requirements for handrails and stanchions for rapid, light, and commuter rail vehicles, consideration should be given to the proximity of handrails...
-
American Standard Yorkville 1.1 gpf FloWise Right Height Elongated Pressure Assisted Toilet
Built to stand the test of time and handle years of high use, there is an American Standard commercial toilet that's right for any job....
-
49 CFR Parts 27 and 37: Transportation for Individuals With Disabilities; Reasonable Modification of Policies and Practices - Preamble
questions related to transit, you may contact Bonnie Graves, Office of Chief Counsel, Federal Transit Administration, same address, Room E56-306, 202-366-0944, bonnie.graves@dot.gov; and, for rail...
-
1015.2 Where required
On the loading side of station platforms on fixed guideway transit or passenger rail systems....
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Restaurants and Cafeterias: ADA Standard Section 206.2.5
Section 206.2.5 covers scoping requirements in the most current ADA Standards for accessible routes in restaurants and cafeterias
-
Mockett SDH1-SSS Sliding Door Hardware Set
Material: High quality stainless steel Surface: Satin Door weight capacity: 150lb Rail bar is 78-3/4" in length. For use with openings of 30" - 44"...
-
M303.3.1 Vertical (Section-by-Section Analysis)
The MDE NPRM proposed that for equipment with a change in level at the entry to the wheelchair space, level changes of up to ¼ inch high are permitted to be vertical....
