These specifications are derived from requirements for rail vehicles and represent compromises between space needed for use and constraints imposed by vehicle dimensions....
Search Results "High Speed Rail"
-
B. Restrooms
-
III. Handrails and Stanchions
Handrails and Stanchions In addition to the requirements for handrails and stanchions for rapid, light, and commuter rail vehicles, consideration should be given to the proximity of handrails...
-
American Standard Yorkville 1.1 gpf FloWise Right Height Elongated Pressure Assisted Toilet
Built to stand the test of time and handle years of high use, there is an American Standard commercial toilet that's right for any job....
-
49 CFR Parts 27 and 37: Transportation for Individuals With Disabilities; Reasonable Modification of Policies and Practices - Preamble
questions related to transit, you may contact Bonnie Graves, Office of Chief Counsel, Federal Transit Administration, same address, Room E56-306, 202-366-0944, bonnie.graves@dot.gov; and, for rail...
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
1015.2 Where required
On the loading side of station platforms on fixed guideway transit or passenger rail systems....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Restaurants and Cafeterias: ADA Standard Section 206.2.5
Section 206.2.5 covers scoping requirements in the most current ADA Standards for accessible routes in restaurants and cafeterias
-
Mockett SDH1-SSS Sliding Door Hardware Set
Material: High quality stainless steel Surface: Satin Door weight capacity: 150lb Rail bar is 78-3/4" in length. For use with openings of 30" - 44"...
-
M303.3.1 Vertical (Section-by-Section Analysis)
The MDE NPRM proposed that for equipment with a change in level at the entry to the wheelchair space, level changes of up to ¼ inch high are permitted to be vertical....
-
R402.4 Reduced Vertical Clearance
Guardrails or other barriers to pedestrian travel shall be provided where the vertical clearance is less than 2 m (6.7 ft) high....
-
C. Door Hardware
Is the door hardware (lever, pull, panic bar, etc.) usable with one hand, without tight grasping, pinching or twisting of the wrist, since many persons with disabilities may not have high...
-
VARIABLE MESSAGE SIGN (VMS) CHARACTERS
High resolution VMS characters have vertical pixel counts of 16 rows or greater. Low resolution VMS characters have vertical pixel counts of 7 to 15 rows....
-
§ 38.23(c)(2) Ramp surface
The ramp surface shall be continuous and slip resistant; shall not have protrusions from the surface greater than 1/4 inch high; shall have a clear width of 30 inches; and shall accommodate...
-
707.7.2 Characters
Characters shall be 3/16 inch (4.8 mm) high minimum based on the uppercase letter "I"....
-
Kompan, Inc. Solitaires Spinners - GXY926 - Miram Video
Made for older children and teenagers, Miram is part of Kompan's extensive range of novel, high quality playground equipment....
-
American Standard Yorkville 1.6 gpf Right Height Elongated Pressure Assisted Toilet
Built to stand the test of time and handle years of high use, there is an American Standard commercial toilet that's right for any job....
-
Wagner Instruments Mark-10 M3 Digital Force Gauge
graphic liquid crystal display of: Primary force reading - 5 digit Peak force readings - maximum tension & compression Set point force - programmed high...
-
Problem One (Ramps)
Problem One: There is a six inch high step on the accessible route that has a ramp that is only three feet long, making the ramp too steep and, therefore, inaccessible....
-
11B-308.1.1 Electrical switches
receptacle outlets, appliances or cooling, heating and ventilating equipment, shall comply with Section 11B-308 except the low reach shall be measured to the bottom of the outlet box and the high...
-
4.15.3 SPOUT LOCATION
The spout shall provide a flow of water at least 4 in (100 mm) high so as to allow the insertion of a cup or glass under the flow of water....
-
Side Reach [§308.3]
Fuel Dispensers The operable parts of fuel dispensers located on existing curbs can be up to 54” high....
-
11B-707.7.2 Characters
Characters shall be 3/16 inch (4.8 mm) high minimum based on the uppercase letter "I"....
