This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
Search Results "Bathtub Clearance"
-
Paperwork Reduction Act
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
807 Holding Cells and Housing Cells
The Board has added clarification that at least one water closet, lavatory, and bathtub or shower, where provided, must be accessible (807.2.4)....
-
1134A.7, Item 1
In locations where water closets are adjacent to non-grab bar walls, vanities, lavatories or bathtubs, the centerline of the fixture shall be a minimum of 18 inches (457 mm) from the obstacle...
-
Lavatories and Mirrors [4.19]
In those few toilet or bathrooms permitted to be adaptable, base cabinetry is allowed as long as required clear floor space and knee and toe clearances are available when the cabinet is...
-
Don-Jo Mfg., Inc. Pull Plate CFC7015
Number CFC7015 Dimensions 3-1/2" x 15" Ctc 6" Diameter 3/4" Projection 2-1/4" Clearance 1-...
-
M301.4 Lift Compatibility
An overhead lift (and possibly a gurney-based transfer) may be used in lieu of the provisions for clearances in or around the base of equipment to accommodate the legs of portable floor...
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
Forward Approach
Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
R306.2 Pedestrian Signal Phase Timing
All pedestrian signal phase timing shall comply with section 4E.06 of the MUTCD (incorporated by reference, see R104.2) and shall be based on a pedestrian clearance time that is calculated...
-
11B-307.4.1 Guy braces
FIGURE 11B-307.4.1 GUY BRACES FIGURE 11B-307.4 VERTICAL CLEARANCE...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
-
Don-Jo Mfg., Inc. Pull Plate 7011
Number 7011 Dimensions 3-1/2" x 15" Ansi J405 Ctc 5-1/2" Diameter 5/8" Projection 2" Clearance...
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
4.2.5* Forward Reach
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b)....
