Handrail Clearance and Cross Section [§505.5, §505.7] Surface requirements and clearances facilitate a power grip along the length of handrails....
Search Results "Extended Floor Surface"
Commonly Searched Documents
-
Handrail Clearance and Cross Section [§505.5, §505.7]
- Smith System Husky Clover Activity Table
-
T302.3 Openings
Openings in walking surfaces shall not allow the passage of a sphere more than 5/8 inch (16 mm) in diameter....
- Diversified Woodcrafts ADA Instructor's Desk 1214K-L-ADA
-
Inpro Corporation ENDURANT® Partition Urinal Screen
Requires the Premium User plan or above. (Login or upgrade your account!)
-
Neo-Metro Urinal Divider Model Number: 8949-N 3D Model
Requires the Premium User plan or above. (Login or upgrade your account!)
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1014.2.1.1.2 Slope
The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction....
-
1014.2.1.1.2 Slope
The slope of the surface of the clear ground space shall not be steeper than 1:48 in any direction....
- Precision Safe Sidewalks LLC Sidewalk Trip Hazard Repair Service
-
A. Measuring Slope and Cross Slope
First, observe the general slope of the surface and place the builders' level on the pavement at the steepest point parallel to the direction of the slope....
-
1013.3 Slope
The slope of the surface of tent pads, tent platforms, and clear ground spaces shall not be steeper than 1:48 in any direction....
-
1013.3 Slope
The slope of the surface of tent pads, tent platforms, and clear ground spaces shall not be steeper than 1:48 in any direction....
-
604.3.2 Overlap
around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible routes, clear floor...
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
11B-805.7 Built-in cabinets and work surfaces
work stations, equipment consoles, clean and soiled utility cabinets, and storage areas; and shall comply with Sections 11B-225 _|Storage|_ and 11B-902 _|Dining Surfaces and Work Surfaces...
-
Background
Some engineered wood fiber (EWF) and chipped wood surfaces on playgrounds are difficult for those who use mobility aids, such as wheelchairs and walkers, because the surfaces are soft and...
- Populas Vox Corner Office Workstation
-
Controls [§404.3.5]
Clear floor space at controls must be located outside the door swing to prevent users from getting hit by the door....
-
M304.2.2 Standing Supports
Standing supports shall be provided on two sides of the standing surface and shall comply with M305.3....
-
Allowances for Typical Roadway Geometry
for Typical Roadway Geometry The 1991 ADAAG and 2004 ADA and ABA Accessibility Guidelines specify a maximum running slope of 5 percent and maximum cross slope of 2 percent for walking surfaces...
-
31.1 Q. Can a water closet (toilet) be located in an alcove with a wing wall?
Yes, as long as the necessary clear floor space shown in Figure 7(a) is provided....
-
11B-407.4.1 Car dimensions
Exception: In existing buildings, where existing shaft configuration prohibits strict compliance with Section 11B-407.4.1, existing elevator car configurations that provide a clear floor...