Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
Search Results "Surface Material"
-
11B-407.4.10.2 Surfaces
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
4.7.9.1 General
Where utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent, but not less than one in each accessible space,...
-
1991 / 1994 ADA Standards - Plan Review Tool - Slopes
1991 / 1994 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "1991 / 1994 ADA Standards - Plan Review Tool - Slopes" (354 KB) * * * * * * *
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
M301.3.1 Transfer Supports
A.1) A transfer support will extend horizontally along the side of the patient scanning/imaging table at least the minimum width of the transfer surface, but in all cases a 28 inches minimum...
-
What is a good un-official "working" definition of "work surface"?
11B-805.7 goes on to list numerous items that would/could be included in the broad verbiage of "Built-in cabinets, counters and work surfaces"....
-
Adjustable Height Range Considered
to make up the difference between the two surfaces, in one direction or the other....
-
5.3.2 Transfer Sides Recommendations for M301
the long side of the surface....
-
1.2.2 Alternative materials, design and methods of construction and equipment
1.2.2 Alternative materials, design and methods of construction and equipment. ...
-
1. Standing Supports
The proposed rule included a provision requiring standing supports on each side of the standing surface and compliance with the technical requirements for standing supports in proposed M305.3...
-
[A] 104.11 Alternative materials, design and methods of construction and equipment
The provisions of this code are not intended to prevent the installation of any material or to prohibit any design or method of construction not specifically prescribed by this code, provided...
-
5.4.2.1 Transfer Support Length for Stretchers
5.4.2.1 Transfer Support Length for Stretchers. Transfer supports on stretchers should be a minimum of 15 inches long.
-
Accessible Parking Space
Accessible Parking Space
-
Appendix to Part 38—Guidance Material
[56 FR 45756, Sept. 6, 1991, as amended at 63 FR 51702, 51703, Sept. 28, 1998; 79 FR 21407, Apr. 16, 2014] This appendix contains materials of an advisory nature and provides additional...
-
[A] 104.11 Alternative materials, design and methods of construction and equipment
ETA Editor's Note DSA-AC has adopted Section 104.11 as follows, effective July 1, 2015: [A] 104.11 Alternative materials, design and methods of construction and equipment. ...
-
M301.3.1 Transfer Supports (Section-by-Section Analysis)
The only change in the final rule was to update the cross reference to applicable transfer surfaces to accommodate the changes made to transfer surfaces, described above in Section IV.B.1...
-
1.2.3 Alternative materials, design and methods of construction and equipment
The provisions of this code are not intended to prevent the installation of any material or to prohibit any design or method of construction not specifically prescribed by this code, provided...
-
1.2.3 Alternative materials, design and methods of construction and equipment
The provisions of this code are not intended to prevent the installation of any material or to prohibit any design or method of construction not specifically prescribed by this code, provided...