rehabilitation, reconstruction, historic restoration, changes or rearrangement in structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
Search Results "Height Adjustable"
Filters
Commonly Searched Documents
-
§ 37.3 Alteration
-
Hoyer Ascend Stand-Up Lift
Features Supportive knee tray with one-hand adjustment Removable foot tray allows the Ascend to be used as a walking aid Unrivaled range of movement Transfers...
-
Bradley 2-Station Frequency Lavatory System FL-2H & FL-2L
With its patented design, the multi-height Frequency Lavatory System comfortably provides hand-washing access for adults, children, and those with disabilities....
-
7.4 Legal and Regulatory Considerations
accessible” because it conforms to the new standards, this would be a marketing claim that FDA would review to verify that the claim is accurate, for example, by verifying the device’s range of height...
-
Pilot Rock LDW-36/18 Campfire Ring
Accessible campfire ring Model LDW-36/18/TB includes a full-height outer ring to serve as a heat barrier for the inner ring. ...
-
1125B.3
SECTION 1125B - STORAGE 1125B.3 Height. Accessible storage spaces shall be within at least one of the reach ranges specified in Sections 1118B.5 and 1118B.6....
-
Notes
Notes GG Analysis of Seat Heights for Wheeled Mobility Devices. The study is available at http://udeworld.com/analysis-of-seat-height-for-wheeled-mobility-devices....
-
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Features Addressed in Technical Criteria Types Of Equipment To Which Technical Criteria Applies Supine, prone, or side-lying position (M301) Transfer surface, including height...
-
1134A.5, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. (See Figure 11A-9G)....
-
1016.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
1134A.5, Item 2
The grab bar reinforcement shall be a minimum of 6 inches (152.4 mm) nominal in height. (See Figure 11A-9G)....
-
ALTERATION
resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
Dressing, Fitting, or Locker Rooms
Operating mechanisms provided on accessible lockers must also meet ADAAG provisions for their operation and height....
-
I. Introduction
The purpose of this Minority Report is to make a formal recommendation for a minimum transfer surface low height of 19 inches for diagnostic imaging medical equipment....
-
R308.1.2.1 Platform and Vehicle Floor Coordination
The Department of Transportation regulations (49 CFR parts 37 and 38) require the height of the vehicle floor and the station platform to be coordinated so as to minimize the vertical and...
-
T703.1 General
The symbol shall have a background field height of 4 inches (100 mm) minimum. The symbol and its background shall have a non-glare finish....
-
407.8.2 Side Reach
Where a side reach requires a reach over a portion of the ICT, the height of that portion of the ICT shall be 34 inches (865 mm) maximum....
-
Standard Units
Standard Units Units at conventional heights for use by standees are considered accessible to people who may bend or stoop with difficulty....
-
407.12.2 Side Reach
Where a side reach requires a reach over a portion of the ICT, the height of that portion of the ICT shall be 34 inches (865 mm) maximum....
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion of the automated teller machine or surround is not more than 10 in (255 mm), the maximum height...
-
A4.13.9 DOOR HARDWARE
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) form its bottom edge and be centered across the top....
-
11B-306.3.4 Clearance reduction
inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (152 mm) in height...
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
