measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth is measured between the perineal cutout and the hinge...
Search Results "Hinge Side Clearance"
-
MEASUREMENT TECHNIQUE
-
4.13.11* DOOR OPENING FORCE
(a) exterior hinged doors: (Reserved)....
-
2.2.6 Door Use
clearance > 1525 mm > 1525 mm > 1525 mm Pull side clearance > 1525 mm > 1525 mm > 1525 mm Push side latch side...
-
1010.1.7 Thresholds
In occupancy Group R-2 or R-3, threshold heights for sliding and side-hinged exterior doors shall be permitted to be up to 7¾ inches (197 mm) in height if all of the following apply:...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
1118B.6
SECTION 1118B - SPACE ALLOWANCE AND REACH RANGES 1118B.6 Side reach. ...
-
Accessible Parking Video Fact Sheet
Troy Balthazor, ADA Specialist for the Great Plains ADA Center, gives an overview of accessible parking requirements from the 2010 ADA Standards for Accessible Design. Technical...
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
Lavatory & Accessory Layouts
The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper towel and drop it into the receptacle before exiting.
-
Clear Deck Space
This will allow persons using a wheelchair to turn around and access the wall, depending on the side they can best use to transfer....
-
11B-809.10.5.4 Bathtub enclosures
Hinged doors shall open outward. Glazing used in doors and panels of bathtub enclosures shall be fully tempered, laminated safety glass or approved plastic....
-
11B-809.10.5.4 Bathtub enclosures
Hinged doors shall open outward. Glazing used in doors and panels of bathtub enclosures shall be fully tempered, laminated safety glass or approved plastic....
-
B. Measuring Clear Passage at Doors
Verifying the clear passage width at standard hinged doors requires an understanding of exactly where to measure....
-
Grab Bars
If only one bar is provided, the clearance must be a minimum of 24 inches on each side of the bar....
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
Water Closet Clear Floor Space in Toilet Compartments
Other criteria for toilet rooms, including turning space, maneuvering space at doors, and clearances at other fixtures, typically results in additional clearance at water closets not in...
-
AJW Architectural Products U719 96"W x 48"H J-Mold Mirror - Four Sided Frame - Plate Glass
Product Features Fabricated of #18 gauge stainless steel with #4 satin finish Mirror features a "J" type channel frame Multiple reflective surfaces available Mirror comes...
-
Figure 1003.3.1 Boat Slip Clearance – Drawing from the U.S. Access Board
-
Figure 1003.3.2 Boarding Pier Clearance – Drawing from the U.S. Access Board
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
M302.4 Lift Compatibility (Section-by-Section Analysis)
M302.4.1) or clearance around base (proposed M302.4.2) technical requirements....
-
Accessible Mats for Beach and Outdoor Events
Access Trax’s Accessible Mat Features: Custom configurations: Each mat connects on all 4 sides Easily connect mats with durable hinges (no tools required)....
