Exception: Where the clear width at the turn is 60 inches (1524 mm) minimum compliance with Section 11B-403.5.2 shall not be required....
Search Results "Compliance Agreement"
Filters
Commonly Searched Documents
-
11B-403.5.2 Clear width at turn
-
§ 37.5(i)(1) Private entity-private transport
This obligation includes, with respect to the provision of transportation services, compliance with the requirements of the rules of the Department of Justice concerning eligibility criteria...
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
11B-403.5.2 Clear width at turn
Exception: Where the clear width at the turn is 60 inches (1524 mm) minimum compliance with Section 11B-403.5.2 shall not be required....
-
419.7 Accessibility
ETA Editor's Note California Building Code Chapters 5 through 8 are not adopted by the Division of the State Architect - Access Compliance (DSA-AC), and have been omitted....
-
1133A.7 Knee and toe space
space, when required by Section 1133A, shall comply with Section 1138A.2 and the following: The knee and toe space shall be clear and unobstructed, or removable base cabinets in compliance...
-
Site Selection
You may wish to include an affirmative statement of compliance, or allocation of responsibilities between landlord and tenant, in any rental agreements or contracts you enter with meeting...
-
A. Arena Assembly Seating:
PSE shall provide at least 99 wheelchair accessible seats in The Palace in compliance with the wheelchair space requirements set forth in §802.1 of the 2010 Standards, in accordance...
-
11B-202.5 Alterations to qualified historic buildings and facilities
EXCEPTION: Where the State Historic Preservation Officer or Advisory Council on Historic Preservation determines that compliance with the requirements for accessible routes, entrances, or...
-
TRAINING
The curricula and materials used in the trainings required by these paragraphs shall be consistent with the provisions of this Agreement. 26....
-
INTRODUCTION
The document embodies an agreement to minimize the differences between the standards previously used by four agencies (the General Services Administration, the departments of Housing and...
-
General: ADA Standard Section 223.1
Section 223.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for medical care and long-term care facilities.
-
11B-707.4 Privacy
Justice considers the communication-related elements of ATMs to be auxiliary aids and services, rather than structural elements, to which the Safe Harbor allowance for elements built in compliance...
-
Evan Terry Associates
Our goal of providing this high quality service is achieved with a staff of 20 including 8 registered architects, 1 intern architect, 1 registered landscape architect, and 2 access compliance...
-
Implementation Approach and Schedule
The Interactive Travel Services Association (ITSA) opposed the phased implementation timeline and urged the Department to impose a single compliance deadline of at least 18 months after...
-
Section 35.150(b)(2) Safe harbor (Section-by-Section Analysis)
Once the compliance date is reached, such noncompliant facilities or elements must be made accessible in accordance with the 2010 Standards....
-
403.5.2 Clear Width at Turn
EXCEPTION: Where the clear width at the turn is 60 inches (1525 mm) minimum compliance with 403.5.2 shall not be required. Figure 403.5.2 Clear Width at Turn...
-
1.9.1.8 Adopting agency identification
ETA Editor's Note Sections from California Building Code Chapter 1 not adopted by Division of the State Architect - Access Compliance (DSA-AC) omitted. ...
-
11B-403.5.2 Clear width at turn
Exception: Where the clear width at the turn is 60 inches (1524 mm) minimum compliance with Section 11B-403.5.2 shall not be required. FIGURE 11B-403.5.2 CLEAR WIDTH AT TURN...
-
2. Effective Date
On March 15, 2012, compliance with the 2010 Standards will be required for new construction and alterations and barrier removal....
-
5. CONSTRUCTION TOLERANCES
CONSTRUCTION TOLERANCES: While it is always advisable to avoid design requirements that are at or near dimensional thresholds, construction tolerances may be used when evaluating the compliance...
-
Fixtures
For purposes of compliance with TAS 604.3.2, the reference to “fixture” shall mean the plumbing fixtures identified in TAS 213.3 and baby changing tables which are identified as convenience...
-
Gaps
However, if compliance with those measurements is not operationally or structurally feasible, operators may use bridge plates, ramps or other devices....
