Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
Search Results "Clearance Around Base"
Filters
Commonly Searched Documents
-
11B-407.4.10.1 Location
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
Resting Intervals on Trails
This doesn't mean that another space must be provided for turning around or as a passing space in addition to the resting space....
-
Section 37.127 Complementary Paratransit for Visitors
The local provider need serve someone based on visitor eligibility for no more than 21 days. After that, the individual is treated the same as a local person for eligibility purposes....
-
BACKGROUND
This matter is based upon a complaint filed with the United States Department of Justice (“Department”) by a University student who is blind (“Complainant”), who alleged that he was unable...
-
Don-Jo Mfg., Inc. Pull Plate CFC7015
Number CFC7015 Dimensions 3-1/2" x 15" Ctc 6" Diameter 3/4" Projection 2-1/4" Clearance 1-...
-
5.8.2.7.1 Mammography Chair Footrest Recommendation
Footrest Recommendation The Committee recommends that the mammography chair meet the elements of M302 with the additional requirement that any footrests must accommodate and ride over the base...
-
F204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance...
-
204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance...
-
4.1.6(3)(c)(iii)
For example, an elevator of 47 in by 69 in (1195 mm by 1755 mm) with a door opening on the narrow dimension, could accommodate the standard wheelchair clearances shown in Figure 4....
-
4.2.6* Side Reach
If the side reach is over an obstruction, the reach and clearances shall be as shown in Fig 6(c)....
-
4.18.3 Clear Floor Space
Urinal shields that do not extend beyond the front edge of the urinal rim may be provided with 29 in (735 mm) clearance between them....
-
4.1.6(4)(d)
(i) Where existing elements prohibit strict compliance with the clearance requirements of 4.13.5, a projection of 5/8 in (16 mm) maximum will be permitted for the latch side door stop....
-
4.2.5 FORWARD REACH
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b). Figure 5 Forward Reach...
-
4.18.3 CLEAR FLOOR SPACE
Urinal shields that do not extend beyond the front edge of the urinal rim may be provided with 29 in (735 mm) clearance between them....
-
§ 38.159(a)(1) General
., lift or ramp) complying with paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a securement location....
-
§ 37.77(c)(5)
(5) Restrictions or priorities based on trip purpose;...
-
4.3.9 Doorway Design
The lack of differences between the findings for the passage task on the pull sides of Doors 1, 800 mm (31.5 in.) latch clearance, and Door 2, 406 mm (16 in.) latch clearance, demonstrate...
-
Military Installation
A base, camp, post, station, yard, center, homeport facility for any ship, or other activity or operation under the jurisdiction of the Department of Defense, including any leased facility...
-
§ 38.23(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.95(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.125(b)(1) Design load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
§ 38.83(b)(1) Design Load
Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift depends for support of the load, shall have a safety factor of at least six, based...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
