The following technical criteria in the proposed standards are based on the 2004 ADA and ABA Accessibility Guidelines: • Height of transfer surfaces on diagnostic equipment used by patients...
Search Results "Work Surface"
-
2004 ADA and ABA Accessibility Guidelines
-
19 Inch Low Height
transfer surface....
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply with M305.3.1.2...
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface....
-
M301.2.1 Adjustability (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface height range for diagnostic equipment used by patients in the supine, prone, or side-lying position of 17 inches minimum and 19 inches maximum....
-
§ 38.23(c)(8) Handrails
them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
R304.5.3 Cross Slope
R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
-
Addendum F: Relative Height Differences
Relative heights were calculated for high and low transfers for all three protocols. Refer to Addendum A for the definition of relative height. The following tables F1-F3 represent...
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
1.1.12 Ramp cross slope
1.1.12 Ramp cross slope. Measure for overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the...
-
1012.5 Slope
This section requires the slope of the surface of parking spaces and pull-up spaces to not be steeper than 1:48 in any direction....
-
Passenger Loading Zones [4.6.6]
A level surface (maximum 2% slope in any direction) for both the space and aisle is important for wheelchair transfer to and from vehicles and deployment of vehicle lifts or ramps....
-
4.34.6 KITCHENS
Accessible or adaptable kitchens and their components shall be on an accessible route and shall comply with the requirements of 4.34.6.
-
4.8.5* HANDRAILS
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface....
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
Adaptive Surfing Makes the Ocean Accessible for People Who Use Wheelchairs - Rolling On, Episode 5
See how Arianny Ramirez rides Rockaway Beach’s waves on a surfboard—even though she needs a wheelchair to get around on land. Go to g.co/LGa11y and find out how Local Guides can make...
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
4.6.5 PASSENGER LOADING ZONES
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 in all directions....
-
T402.9 Transitions
Vertical surface discontinuities at transitions from boarding and alighting areas to ramps and bridgeplates shall comply with T302.4....
-
Example: Clinical Suite
This facility includes public and common use areas and employee work areas....
-
11B-809.8 Doors
Door surfaces shall comply with Section 11B-404.2.10. Doors in series shall comply with Section 11B-404.2.6....
