[DSA-AC] An expansion, extension or increase in the gross floor area or height of a building or facility....
Search Results "Head Height"
-
ADDITION
-
11B-703.2.6 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 15 percent maximum of the height of the character....
-
Sample Size Estimation
Data from the maximum and minimum height transfers from protocol A were used for this analysis....
-
SUMMARY OF THE 19-INCH RECOMMENDATION
Access Board’s Medical Diagnostic Equipment Technical Advisory Committee discussed transfer surface height extensively....
-
Notes
Seat heights for males were typically higher than for females....
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
11B-604.5 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped grab bar meeting the dimensional requirements of Sections 11B-604.5.1 and 11B-604.5.2 shall...
-
[A] ADDITION
[DSA-AC] An expansion, extension, or increase in the gross floor area or height of a building or facility....
-
Side Reach [4.2.6]
Since the height of reach decreases with depth, the maximum high reach is limited to 46 inches over obstructions no more than 24 inches deep and 34 inches high....
-
1012.3 Opening limitations
Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102 mm) sphere cannot pass through any opening up to a height of 34 inches (864 mm)....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
Attachment H: Modifications to Altered Facilities
Attachment H: Modifications to Altered Facilities
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
M301.3 Transfer Supports
o Rationale: This is to accommodate the articulation that is necessary for the head and back support on stretchers....
-
Test Procedures
ASTM F 1292-99 test specifications (ASTM 1999a) and F355-95 test methods (ASTM 1995) were used at a test drop height of 3.05 m (10.0 ft) and 1.83 m (6.0 ft), respectively....
-
M301.2.3 Transfer Sides
The configuration of stretchers will not allow for unobstructed access to a transfer surface located at either the foot end or head....
-
The Roles of the Access Board and the Department of Justice
The Board consists of thirteen public members appointed by the President, of whom the majority must be individuals with disabilities, and the heads of twelve federal departments and agencies...
-
Undue Burden
This determination can only be made by the head of the public entity or his or her designee and must be accompanied by a written statement of the reasons for reaching that conclusion....
-
Haws AXION® MSR Barrier-Free Recessed Eye/Face Wash 7655WCC
Model 7655WCC barrier-free eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending)....
-
ADDENDUM TO PHASE I FINAL REPORT: Points of Clarification
The Adjustable Height protocol included two types of transfers, a transfer to a higher height and a transfer to a lower height relative to the mobility device's seat to floor height....
-
Re: Service Counters
The entire depth of the lowered counter at 34" max height must be provided to allow for this unimpeded interaction instead of the higher employee counter condition which prevents equal access...
-
Q2: Milling a Road Surface
What constitutes “overlays of additional material to the road surface” with respect to milling, specifically, when a roadway surface is milled and then overlaid at the same height (i.e.,...
