The sloped, die-cast metal endcaps provide added support, protecting the device and the door against the heaviest impact....
Search Results "Counter Slope"
Filters
Commonly Searched Documents
-
Allegion Von Duprin 94/95 Series INPACT Recessed Exit Device
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
As the FloorPro® travels the survey line, many inclinometer slope readings are gathered over a 1" interval every 6", averaged and average saved as the 6" slope....
-
F205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
Visual Busyness (slide 13)
So I think what you have to do is use the contrast on the edges of things to tell you where the edge of the counter is, to tell you where the floor meets the wall, to tell you when something...
-
Recommendations for Future Research
• Additional research would be required to determine the validity and repeatability of the Rotational Penetrometer measurements on surfaces with slopes greater than 5%....
-
11B-303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (12.7 mm) high maximum shall be beveled with a slope not steeper than 1:2. [2010 ADAS] Advisory 303.3 Beveled. ...
-
Thresholds at Doorways
The 1991 Standards and the 2010 Standards require raised thresholds that exceed ¼ inch in height to be beveled on each side with a slope not steeper than 1:2....
-
Clear Deck Space
Clear Deck Space Clear deck space of 60 by 60 inches minimum, with a slope of not more than 1:48, must be provided at the base of a transfer wall....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space,head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
4(2)
(2) In single-story dwelling units, changes in level within the dwelling unit with heights between 1/4 inch and 1/2 inch are beveled with a slope no greater than 1:2....
-
303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
-
A. Accessible Entrance
Accessible Entrance Having a way to get into the emergency shelter on a surface that is firm, stable, slip resistant, without steps or steep slopes, and wide enough for a person using...
-
Outdoor Conditions [4.8.8]
A slope up to 2% is allowed at landings for adequate drainage....
-
4.4.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
Electronic instruments
Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle warehouses, these devices can be used to measure slope flatness....
-
Three Additional Features for Van-Accessible Parking Spaces
accessible" and the international symbol of accessibility mounted high enough so the sign can be seen when a vehicle is parked in the space 96" min. width access aisle, level (max. slope...
-
Program Accessibility
For example, if there is not enough space to install a ramp with a slope no steeper than 1:12, a public entity may install a ramp with a slightly steeper slope....
-
Lowered section for bar
Can anyone show me where a folding lower section of the bar counter can't be used as long as it meets the other requirements? This is not for designing a new bar....
-
Salsbury Industries See Through Metal Locker Double Tier 3 Wide
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries See Through Metal Locker Double Tier 1 Wide
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries See Through Metal Locker Triple Tier 3 Wide
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries See Through Metal Locker Triple Tier 1 Wide
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
AJW Architectural Products U590 1.6 Gallon Sanitary Napkin Disposal w/ Keyed Access Panel - Surface Mounted
Cover: Fabricated of #22 ga stainless steel #4 satin finish with embossed handles on each side and sloped top. Bottom Panel: #22 ga hinged and locked for removal of contents....
