Clear floor spaces 30 inches (762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the following...
Search Results "Abrasive Surface"
-
11B-809.9.1 Clear floor space
-
Key Study findings:
When multiple transfers are required to reach higher or lower surfaces 15.2% of the participants in this study could not complete them at any height (11 out of 72 participants; 8 of which...
-
Sales and Service Counters, Teller Windows, Information Counters [7.2]
Sales and Service Counters, Teller Windows, Information Counters [7.2] ADAAG generally specifies accessible counter heights up to 34 inches [4.32] but allows a height up to 36...
-
1.1.7 Measurement of parking areas
1.1.7 Measurement of parking areas. Only accessible access aisles and passenger loading zones that are part of a larger parking area need to be measured. These areas should be...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance (§505.5, §505.7)
-
M305.3.1 Length (Section-by-Section Analysis)
In the MDE NPRM, the Access Board proposed a gripping surface length of four inches minimum for horizontal standing supports. No public comments were submitted on this requirement....
-
surface mounted toilet paper dispensers
Surface mounted dispensers are now being used for design and construction convenience, and they appear to pose an unnecessary hazard of injury due to the amount they project from the wall...
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
11B-805 Medical care and long-term care facilities
SECTION 11B-805 Medical care and long-term care facilities 11B-805.7 Built-in cabinets and work surfaces....
-
Why a smooth surface door or kickplate is important
Remember that the latch that hits the push rim is nicking the surface your fingers have to grasp thousands of times a day for years....
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
Figure 505.7.2 Handrail Non-Circular Cross Section – Drawing from the U.S. Access Board
-
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment
The transfer or positioning support should be oriented horizontally on imaging equipment with transfer surfaces....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
M301.2.3 Size
The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides....
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
4.7.9.1 General
Where utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent, but not less than one in each accessible space,...
-
1991 / 1994 ADA Standards - Plan Review Tool - Slopes
1991 / 1994 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "1991 / 1994 ADA Standards - Plan Review Tool - Slopes" (354 KB) * * * * * * *
