Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
Search Results "Abrasive Surface"
Filters
Commonly Searched Documents
-
5.4.1 Transfer Support Location for M301 and M302
-
Section G: Ramps
(§405.7.4) G8 If the rise of the ramp is greater than 6", are handrails provided that are between 34" and 38" above the ramp surface?...
-
Ramps M303:3.3, 3.3.1, 3.3.2
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
-
5.4.2 Transfer Support Length for M301 and M302
The purpose of a minimum length is to ensure that there is a minimum gripping surface available to support positioning and repositioning during a transfer....
-
TotTurf® Synthetic Grass: Play Spaces
Description Tot Turf Play Spaces is a line of natural looking, soft, attenuating turf surfacing perfect for playgrounds....
-
Which transition type do users with disabilities prefer?
When a sidewalk slopes more than 2% in the direction of travel and a walk with a maximum 2% cross slope intersects it, which transition segment type provides the safest usability for...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Outside Surfaces
Subsets of the subjects also traveled over outdoor surfaces around the area at which they were tested with the accelerometers attached to their chairs and rated those surfaces....
-
EXHIBIT A Required Accessible Elements at QuikTrip Stores
All objects that protrude from surfaces or posts into circulation paths shall comply with ADA Standards § 4.4 and a minimum 80 inch vertical clearance shall be provided in walks, halls,...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
At the point of connection, these features impede the ability to grasp completely around the cross section of the gripping surface....
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Bathroom Do’s and Dont’s
Do. Use a floor drain that extends the length of the shower to prevent water flowing into other areas of the bathroom. This is recommended, even if the floor is sloped near the...
-
Stairway Handrails Requirements in the ADA Standards (§504)
Stairway Handrails Requirements in the ADA Standards (§504) Protruding Objects The ADA Standards address hazards posed by protruding objects, such as standpipe...
-
1133A.1 General
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and maximum...
-
M305.2.3 Height (Section-by-Section Analysis)
Board sought input from the public in question 20 of the MDE NPRM preamble, on whether a transfer support height requirement of 6 inches minimum and 19 inches maximum above the transfer surface...
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
