The 2010 Standards provide, at section 403.3, that the cross slope of walking surfaces not be steeper than 1:48....
Search Results "Ramp Surface"
-
Slope
-
Islands [§406.7]
Islands [§406.7] A 48” min. long separation is necessary between curb ramps so that people using wheelchairs can clear one ramp before negotiating the next....
-
1.1.4
1.1.4 A maximum overall design running slope for exterior accessible ramps of 7.5% (1:13.3 or 1:13) is recommended....
-
How to Measure Ramp Handrail Extensions
This short video considers some of the most common factors required for measuring ramp handrail extensions for compliance surveys....
-
5.2.3 Transfer Surface Measurement
5.2.3 Transfer Surface Measurement. The transfer surface should be measured from the center-point of each side of the transfer surface....
-
Can ramps be portable or provided after construction as an adaptation?
All required ramps and curb ramps must be permanent and installed at the time of construction or alteration with few exceptions....
-
R304.3.1 Turning Space
A turning space 1.2 m (4.0 ft) minimum by 1.2 m (4.0 ft) minimum shall be provided at the bottom of the curb ramp and shall be permitted to overlap other turning spaces and clear spaces....
-
6 [§ 4.7.7]
6 [§ 4.7.7] Detectable warnings are dome-shaped bumps that should cover the entire width and depth of the ramp run....
-
11B-405.7.5 Doorways
Doors, when fully open, shall not reduce the required ramp landing width by more than 3 inches (76 mm)....
-
11B-405.7.5 Doorways
Doors, when fully open, shall not reduce the required ramp landing width by more than 3 inches (76 mm)....
-
5.8.1.2.1 Ramped Entry Slope Recommendations
5.8.1.2.1 Ramped Entry Slope Recommendations The Committee recommends that raised platforms have a ramp with slopes that do not exceed the following: At 0 to 1½ inches, the slope...
-
Detectable Warnings on Curb Ramps
[See subsections ...]
-
T402.2 Design Load
Ramps and bridgeplates 30 inches (760 mm) or more in length shall be designed to support a load of 600 pounds (273 kg) minimum, placed at the centroid of the ramp distributed over an area...
-
Recreational Boating Facilities: ADA Standard Section 206.2.10
Section 206.2.10 covers scoping requirements in the most current ADA Standards for accessible routes to recreational boating facilities
-
9 [§ 4.7.5]
9 [§ 4.7.5] Curb ramps either have flared sides or vertical edges called returned curbs....
-
DSA Drawing 11B-406-2C Curb Ramp Adjoining a Parking Access Aisle with No Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
DSA Drawing 11B-406-6C Curb Ramp Adjoining a Parking Access Aisle with No Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
1005.3.2 Extended Ground or Deck Surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-406.1 General
Curb ramps, blended transitions and islands on accessible routes shall comply with Section 11B-406....
-
11B-406.1 General
Curb ramps, blended transitions and islands on accessible routes shall comply with Section 11B-406....
-
T402.1 General
Ramps and bridgeplates shall comply with T402. Ramps and bridgeplates shall be permitted to fold or telescope....
-
11B-406.1 General
Curb ramps, blended transitions and islands on accessible routes shall comply with Section 11B-406....
-
3. Review the Research Findings About Accessibility Issues for Play Surfaces
study on the accessibility of playground surfaces....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
5.2.2.1 Transfer Surface Width Recommendations for M302 The Committee recommends 21 inches for the minimum width of the transfer surface of examination chairs and other equipment primarily...
