Search Results "Transfer Position"

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3.1 End Transfer Surface

  End transfer surfaces shall be 28 inches (710 mm) wide minimum and 17 inches (430 mm) long minimum. ...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3.2 Side Transfer Surface

  Side transfer surfaces shall be 28 inches (710 mm) wide minimum and 28 inches (710 mm) long minimum....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.3 Transfer Surface Measurement Recommendation for M301 and M302

  The transfer surface dimensions do not include headrests, footrests, or similar supports for body extremities that do not support the patient’s overall body position....

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.1 Location (Section-by-Section Analysis)

  The MDE NPRM proposed that transfer supports be located within reach of the transfer surface and not obstruct transfer onto or off of the surface when in position (proposed M305.2.1)....

• Federal Documents > Technical Assistance > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment - Example Applications of Proposed Standards
  Figure M3: Overview of M302 Diagnostic Equipment for Use by a Patient in a Seated Position

  [See subsections ...]

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4 Transfer Supports Recommendations

  5.4 Transfer Supports Recommendations...

• State and Local Documents > Codes and Standards > 2022 California Standards
  11B-1008.3.2 Transfer steps

  Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1.1 Transfer Surface Width

  5.2.1.1 Transfer Surface Width. The transfer surface should be 28 inches wide minimum for equipment used by patients in a supine, side-lying, or prone position....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1.2 Transfer Surface Depth

  5.2.1.2 Transfer Surface Depth....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM - Preamble
  Positioning Supports Considered

  patients in a supine, prone or side-lying position, and diagnostic equipment used by patients in a seated position that can be adjusted to a reclined position....

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2 Transfer Supports (Section-by-Section Analysis)

  (Significant Changes – Transfer Supports), the Access Board strengthened the transfer support requirements and added additional requirements in the final rule to ensure that supports are...

• State and Local Documents > Codes and Standards > 2022 California Standards
  11B-1002.6.2 Transfer height

  The height of transfer device seats shall be 14 inches (356 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....

• Research and History > Research Documents > Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report
  Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report

  Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impact  Performance Phase 2: Final Report REPORT PREPARED FOR: U.S ACCESS BOARD, WASHINGTON, DC Authors...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  Gripping Surface Cross Section and Clearances M301, M302, and M305.2

  Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.3 Transfer Surface Measurement

  5.2.3 Transfer Surface Measurement. The transfer surface should be measured from the center-point of each side of the transfer surface....

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M302.2.3 Size (Section-by-Section Analysis)

  The MDE NPRM proposed a transfer surface size for diagnostic equipment used by patients in the seated position of 21 inches wide and 15 inches deep (proposed M302.2.2)....

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M305.2.1 Location

  Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M301.2.2 Sunset Provision (Section-by-Section Analysis)

  (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new requirement of a low height range in M301.2.1...

• Federal Documents > Standards > 2010 ADA Standards
  Shooting Facilities with Firing Positions: ADA Standard Section 243

  Section 243 covers scoping requirements in the current ADA Standards for shooting facilities and firing positions.

• Federal Documents > Standards > 2010 ADA Standards
  Shooting Facilities with Firing Positions: ADA Standard Section 1010

  [See subsections ...]

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....

• State and Local Documents > Codes and Standards > 2022 California Standards
  11B-1010 Shooting facilities with firing positions

  [See subsections ...]