The International Symbol of Accessibility shall be displayed on the exterior of each vehicle operating on an accessible light rail system unless all vehicles are accessible and are not marked...
Search Results "Side Light"
-
§ 38.73(b) Signage
-
407.12.2 Side Reach (Section-by-Section Analysis)
407.12.2 Side Reach (Section-by-Section Analysis) This section specifies proposed requirements for operable parts providing unobstructed or obstructed side reaches....
-
§ 38.79(a)
(a) Floor surfaces on aisles, step treads, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant.
-
§ 38.77 Interior circulation, handrails and stanchions
[See subsections ...]
-
§ 38.83(c)(1) Design load
(1) Design load. Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26...
-
§ 38.83(c)(7) Stowage
(7) Stowage. A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridges plates...
-
§ 38.83(c)(6) Attachment
(6) Attachment—
-
§ 38.83(c) Vehicle ramp or bridge plate
(c) Vehicle ramp or bridge plate—
-
§ 38.83(b)(2) Controls
(2) Controls—
-
§ 38.83(b)(12) Use by standees
(12) Use by standees. Lifts shall accommodate persons using walkers, crutches, canes or braces or who otherwise have difficulty using steps. The lift may be marked to indicate a...
-
§ 38.83(b)(3) Emergency operation
(3) Emergency operation. The lift shall incorporate an emergency method of deploying, lowering to ground level with a lift occupant, and raising and stowing the empty lift if the...
-
§ 38.83(b)(1) Design Load
(1) Design load. The design load of the lift shall be at least 600 pounds. Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift...
-
Side Approach
Side Approach Side reach depth is important to consider in the design and location of sinks....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
18. Q: May a police department create a light duty job category reserved only for incumbent officers without offering identical positions to job applicants?
A police department may create a specific class of light duty jobs that are limited to incumbent police officers....
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
-
Side Entry Openings, and Width and Length of Wheelchair Space
Side Entry Openings, and Width and Length of Wheelchair Space If the wheelchair space can only be entered from the side, the ride must be designed to permit sufficient turning space for...
-
Transfer Sides (M301.2.3 and M302.2.3)
M301.2.3 and M302.2.3 would require the transfer surface to be located so as to provide patients who use mobility devices the option to transfer onto the short side and the long side of...
-
604.5.1 Side Wall
604.5.1 Side Wall....
-
H4
On the pull side of the door, is there at least 18 inches clearance provided on the latch side if the door is not automatic or power-operated?...
-
§ 38.83(c)(4) Ramp barriers
Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
Side Approach and Reach
[See subsections ...]
-
g-iii
Is there clear maneuvering floor space in front of each accessible door (see ADA Standards § Fig. 25) and, on the pull side, is there at least 18 inches clear floor space beyond the latch...
-
The SmartWheel
It used an ultra - light inertial profiler (ULIP) manufactured by Starodub, Inc. in Kengington, MD....