One was a 41 year old men that had a traumatic brain injury and double lower knee amputation, weighted 192 lbs, did not report his height, and had been using a manual wheelchair for twenty...
Search Results "Knee Clearance"
Filters
Commonly Searched Documents
-
Adjustable gap protocol
-
11B-604.5.1 Side wall
2013 CEC) requires a nurse call device at the side wall of a water closet that must be coordinated carefully with the side grab bar at an accessible water closet to ensure that accessible clearances...
-
PEMKO 5" Latching Panic Saddle Threshold No. 2006-T
Allow 3/8" door clearance. ADA Compliant when butted to carpet or tile....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2005-T
Allow 3/8" door clearance. ADA Compliant ThermoSeal insert helps with acoustic performance...
-
Symmetry Limited Use/Limited Application (LU/LA) Elevator
36” wide doors, automatic horizontally sliding, two speed hoistway and car door; full height electric screen Pit depth: Standard 13"" with alternative means (bottom of car clearance...
-
TABLE OF CONTENTS
Firing Positions CHAPTER 3: BUILDING BLOCKS 301 General 302 Floor or Ground Surfaces 303 Changes in Level 304 Turning Space 305 Clear Floor or Ground Space 306 Knee...
-
RECOMMENDATIONS
32.7 m Vertical alignment-crest 49.8 m Recumbent bicyclists 46.7 m Refuge islands 2.5 m Bicyclists with trailers 3.0 m Signal clearance...
-
505.4 Height
Sufficient vertical clearance between upper and lower handrails, 9 inches (230 mm) minimum, should be provided to help prevent entrapment. Figure 505.4 Handrail Height...
-
604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
505.4 Height
Sufficient vertical clearance between upper and lower handrails, 9 inches (230 mm) minimum, should be provided to help prevent entrapment....
-
604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
11B-505.4 Height
Sufficient vertical clearance between upper and lower handrails, 9 inches (230 mm) minimum, should be provided to help prevent entrapment. FIGURE 11B-505.4 HANDRAIL HEIGHT...
-
A4.31.9 Text Telephones
text telephone which is not a single integrated text telephone pay phone unit will require a shelf large enough (10 in (255mm) wide by 10 in (255 mm) deep with a 6 in (150 mm) vertical clearance...
-
Clear Floor Space [4.35.2]
Benches can overlap turning space where clearance (9 inches minimum) is available for toes....
-
Additional Technical Criteria Considered for Handrails on Ramps
These technical criteria are available at http://www.access-board.gov/ada-aba/final.cfm#a505 and address continuity, height, clearance, gripping surface, cross section, surfaces, fittings...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
Re: Lavatories Adjacent to Partitions
I would add that the California text does not specifically require a 'clearance' related to that 18" that we would theoretically be obligated to keep clear....
-
Corbin Russwin Inc. DC46900 Series Safeguard Door Closers
Accommodates minimum door-to-wall clearance on push (closer) side, and 1/8" maximum reveal on pull (holder) side. Minimum top rail: 4"....
-
Horton Automatics ICU/CCU Bi-Fold/Bi-Swing™ Door System
For extra opening width when moving patients or medical equipment, the adjacent Bi-Fold door can be opened along with the Bi-Swing door providing up to 6 ft 8 inches of total clearance....
-
Rockwood Manufacturing Company 110 x 70B Pull Plate 8" CTC Pull 3-1/2" x 15" Plate
Options: • Barrier Free available in 2-1/2" clearance — use BF prefix when ordering (BF110 x 70B). • Advise if door thickness is other than 1-3⁄4"....
-
Rockwood Manufacturing Company 102 x 70B - Pull Plate 5-1/2" CTC Pull 3-1/2" x 15" Plate
Options: • Barrier Free available in 2-1/2" clearance — use BF prefix when ordering (BF102 x 70B). • Advise if door thickness is other than 1-3⁄4"....
-
4.1.2 Surface Design of Examination Tables and Chairs
., while patients’ weights are compressing the table’s or chair’s foam padding).Z This dimension is typically measured at the back of a patient’s knees and includes compression of the seat...
-
Work Areas [4.1.1(3)]
Recommendations: Space for turning within the work area and interior maneuvering clearances at doors, while not required, should be considered, especially where entrapment may be a concern...
