construction or alterations commence after July 26, 1992, but prior to September 15, 2010, then new construction and alterations subject to this section must comply with either UFAS or the 1991 Standards...
Search Results "Referenced Standard"
Filters
Commonly Searched Documents
-
§ 35.151(c)(1)
-
Location of Accessible Routes
The 2010 Standards require all accessible routes to coincide with or be located in the same general area as general circulation paths....
-
Q4.) Are conditions like door closers that require force in excess of the maximum allowed by the standards considered true tolerances or are they simply non-compliance with the maintenance requirements of 35.133 or 36.211?
A4.) In our opinion, the plain language of the term “Construction and Manufacturing Tolerances” does not include adjustable conditions that can meet the detailed requirements when...
-
a. Structural Strength
Industry must follow testing parameters found in other standards.”...
-
1. Rationale for Incorporation by Reference
They are as follows: First, our approach is consistent with that taken by other international standards organizations dealing with this issue....
-
11B-224.5 Dispersion
Access Board's Note to Reader: The Department of Justice’s ADA standards also require the following: Places of lodging. ...
-
11B-224.5 Dispersion
Access Board's Note to Reader: The Department of Justice’s ADA standards also require the following: Places of lodging. ...
-
11B-224.5 Dispersion
Access Board's Note to Reader: The Department of Justice’s ADA standards also require the following: §36.406(c) Places of lodging. ...
-
§ 36.406(c) Places of lodging.
Places of lodging subject to this part shall comply with the provisions of the 2010 Standards applicable to transient lodging, including, but not limited to, the requirements for transient...
-
§35.103(a)
Except as otherwise provided in this part, this part shall not be construed to apply a lesser standard than the standards applied under title V of the Rehabilitation Act of 1973 or the regulations...
-
§ 35.103(a) Rule of interpretation
Except as otherwise provided in this part, this part shall not be construed to apply a lesser standard than the standards applied under title V of the Rehabilitation Act of 1973 or the regulations...
-
Toilet and Bathing Rooms
Section 213 of the 2010 Standards sets out the scoping requirements for toilet and bathing rooms....
-
Issue: Historically Significant Facilities
If alterations are being made to a historically significant property, however, these changes must be made in conformance with the ADA Standards for Accessible Design, (“the Standards”) 28...
-
Introduction
The ADA requires that new construction and alterations to existing facilities comply with the ADA Standards for Accessible Design 1 (Standards)....
-
1 Introduction
Justice published its revised regulations for Titles II and III of the Americans with Disabilities Act of 1990 "ADA" in the Federal Register on September 15, 2010, which include the 2010 Standards...
-
1. Scope
covers the mathematical processing of longitudinal profile measurements to produce a pedestrian pathway roughness statistic called the Pathway Roughness Index (PRI). 1.2 This provides a standard...
-
16(a)(iii)
(iii) The hotel has the required number of rooms for guests with hearing impairments, as set forth in ADA Standards §§ 9.1.2 and 9.1.3, that comply with ADA Standards § 9.3....
-
Appendix 4 – References
Sydney, Australia: Standards Australia International. Australian Standard. (1992)....
-
Existing play areas. (Section-by-Section Analysis)
These guidelines filled a void left by the 1991 Standards....
-
104 Conventions
Section 104.1 of the 2010 Standards notes that dimensions not stated as a “maximum” or “minimum” are absolute....
-
Introduction
True “construction industry tolerances” as defined by the ADA Standards, should not be confused with another concept that we call “Acceptable Measurements.” ...
-
III-7.5190 Dressing and fitting rooms
Technical standards are provided for doors, benches, and mirrors, with less stringent standards for alterations....
-
11B-228.3.2.1 Public use or common use EVCS
TOTAL NUMBER OF EVCS AT A FACILITY1 MINIMUM NUMBER (by type) OF EVCS REQUIRED TO COMPLY WITH SECTION 11B-8121 Van Accessible Standard...
-
11B-505.5 Clearance
[2010 ADA Standards] 505.5 Clearance. Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum....