Open guards shall have balusters or ornamental patterns such that a 4-inch-diameter (102 mm) sphere cannot pass through any opening up to a height of 34 inches (864 mm)....
Search Results "Head Height"
Filters
Commonly Searched Documents
-
1012.3 Opening limitations
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
11B-812.8.7 Location
Signs shall be permanently posted either immediately adjacent to the vehicle space or within the projected vehicle space width at the head end of the vehicle space....
-
Attachment H: Modifications to Altered Facilities
Attachment H: Modifications to Altered Facilities
-
M301.3 Transfer Supports
o Rationale: This is to accommodate the articulation that is necessary for the head and back support on stretchers....
-
Test Procedures
ASTM F 1292-99 test specifications (ASTM 1999a) and F355-95 test methods (ASTM 1995) were used at a test drop height of 3.05 m (10.0 ft) and 1.83 m (6.0 ft), respectively....
-
M301.2.3 Transfer Sides
The configuration of stretchers will not allow for unobstructed access to a transfer surface located at either the foot end or head....
-
The Roles of the Access Board and the Department of Justice
The Board consists of thirteen public members appointed by the President, of whom the majority must be individuals with disabilities, and the heads of twelve federal departments and agencies...
-
Undue Burden
This determination can only be made by the head of the public entity or his or her designee and must be accompanied by a written statement of the reasons for reaching that conclusion....
-
ADDENDUM TO PHASE I FINAL REPORT: Points of Clarification
The Adjustable Height protocol included two types of transfers, a transfer to a higher height and a transfer to a lower height relative to the mobility device's seat to floor height....
-
Q2: Milling a Road Surface
What constitutes “overlays of additional material to the road surface” with respect to milling, specifically, when a roadway surface is milled and then overlaid at the same height (i.e.,...
-
Shower Threshold
The proposed rule specified a maximum threshold height of ½ inch, provided that those greater than ¼ inch are beveled with a slope of 1:2 maximum (608.7)....
-
D. Beds in accessible guest rooms and sleeping rooms
Many individuals with disabilities have urged the Department to regulate the height of beds, particularly in accessible hotel guest rooms, and to require that such beds have clearance under...
-
2.2.3 Functional Reach
Those individuals unable to grasp and/or lift any of the cylinders above shoulder height did not complete the reaches....
-
4.4 Knee and Toe Clearances
Smaller individuals who have heavy thighs, those with high seats and scooter users also have high lap heights....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
605 Urinals
Section 604.5 provides criteria for accessible urinals, including the height and depth, clear floor space, and flush controls....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character. [ECTCR UFAS 4.30.4]...
-
T702.5 Stroke Thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....