Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
Search Results "Head Height"
Filters
Commonly Searched Documents
-
11B-703.2.4 Character proportions
-
11B-805.4.3 Turning space
"Each side" includes both sides and the foot, but does not include the head unless the provision of care requires it. ...
-
11B-805 Medical care and long-term care facilities
"Each side" includes both sides and the foot, but does not include the head unless the provision of care requires it....
-
A. Format and Organization
Main section headings are designated by three numbers (e.g., T101, T102, etc.). Under each main section heading, the text of the guidelines is organized by section levels....
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
611 Washing Machines and Clothes Dryers
Section 611 covers washing machines and clothes dryers and provides specifications for clear floor space, operable parts, and height. Comment....
-
Clear Floor Space [4.34.2] and Reach Ranges [4.34.3]
Maximum reach heights to controls are based on the approach provided. The reach height applies to all controls and elements available for customer activation....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
Rakks® Wall Mounted Standards with Rakks® Brackets
Standards come with drilled and countersunk holes to accept color matched mounting screws (No. 6 x 1-1/4” Philips flat-head), which are included....
-
11B-1009.2 Pool lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space,head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
1009.2 Pool Lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities....
-
11B-1009.2 Pool lifts
Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities....
-
Lateral grab bar use
It can be noted that the lateral grab bar is used by more subjects when the transfer setup increases in level of difficulty (i.e. gap/height in combination or side guard)....
-
Comparison of Transfer Protocols
Highest Transfer Height Obtained Percentiles 5th 25th 50th 75th...
-
1009.5.4 Transfer Steps
Transfer step height shall be 8 inches (205 mm) maximum....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
6.9 Tread Obstacles
Obstacles on beach access routes and their related resting intervals shall not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
