Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in level are...
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
503.4 Floor and Ground Surfaces
-
503.4 Floor and Ground Surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in level are...
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
§ 38.95(c)(2) Ramp surface
(2) Ramp surface....
-
BORA Classic Cooktop Extraction System Installation Video
BORA Classic Cooktop Extraction System Installation Video
-
Engineered Wood Fiber
In addition, there were five sites surfaced with a combination PIP and EWF, and eight sites surfaced with a combination TIL and EWF. ...
-
9.a [§ 4.7.5]
To answer this question you need to determine the slope of the flared sides to make sure it is 10 percent or less....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
Play Areas
Word Fillable Form (0.4MB) Word Non-Fillable Form (0.3MB) PDF Non-Fillable Form (0.3MB)
-
M304.2.1 Slip Resistant
The surface on which the patient stands shall be slip resistant....
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
Inpro Corporation JointMaster® DR Series Seal Expansion Joint Systems
The DR series compression seal stands up to any challenge due to an installation process that is not weather sensitive. Features & Benefits: Heavy pedestrian / Heavy...
-
Access-Able Designs Shower Transfer Bench SH-420-2SDL
Solid or slatted sided tops. Measures 32" W x 16" D Complies w/ ADA 4.21.3 when properly installed 5 year warranty. ...
-
NanoPave® JSS 2-in-1 Joint Stabilizer and Sealer
NP-JSS is also a UV resistant, VOC-free sealant that protects and helps maintain the natural beauty of most paving surfaces. ...
-
1014.1 General
The technical requirements address the entrance to camp shelters (1014.2), including transfer access (1014.2.1) and roll-in access (1014.2.2); and the floor within camp shelters (1014.3)...
-
Lift Compatibility (M301.4 and M302.4)
A patient lift may be the only means of providing access to certain equipment that cannot meet the technical criteria for transfer surface height (see M301.2.1 and M302.2.1) because of the...
-
Shower Stalls [4.21]
ADAAG provides specifications for several types of shower stall designs: roll-in, transfer, and, in hotels (section 9), a combination of the two....
-
Impact Annenuation [sic]
Surface Impact Testing Results per ASTM F 1292: Phase I surfaces (unaged) and Phase II (exposed for 6 months) Surface/ Test Drop 2 G Drop3G Drop2...
-
Tread Obstacles on Trails
A tread obstacle is anything that interrupts the evenness of the tread surface. On trails, tread obstacles often occur as a result of ruts, roots, and rocks in the tread surface....
-
Figure 1009.4.5 Grab Bars for Transfer Walls – Drawing from the U.S. Access Board
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951. Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
