Though Kirola complained of steep paths at Alamo Square Park, the probative value of such testimony is undermined by the lack of any objective data (such as actual measurements of those...
Search Results "Tape Measure"
-
j) Safety Hazards Policy
-
Transfer Access [1014.2.1]
The camp shelter floor at the entrance or opening must be no higher than 19 inches when measured from the clear ground space....
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
This depth measurement is from the center-point of the front and back of the transfer surface as shown in Figure 5.2.1.1....
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
The cross slope is measured perpendicular to the direction of pedestrian travel....
-
Carpet [4.5.3]
A pile thickness up to ½ inch (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
Bails et al.
Research findings from many of the field tests used pre-established sizes and features to measure barriers and problems....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
§ 38.175(a)
All doorways shall have, when the door is open, at least 2 footcandles of illumination measured on the door threshold....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
F105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
A. Accessible Voting Program
The Board agrees that the following temporary measures will be implemented where necessary to make an otherwise inaccessible polling place temporarily accessible during the voting period...
-
§1607.5 General standards for validity studies.
Evidence of the validity of a test or other selection procedure through a construct validity study should consist of data showing that the procedure measures the degree to which candidates...
-
The Brewer Company, LLC
This study measured the physical characteristics of people who use wheeled mobility devices and some of the characteristics of those devices....
-
AJW Architectural Products U133 56 oz. One-Piece Liquid Soap Dispenser - Surface Mounted
Neoprene seals and a stainless return spring will provide a pre-measured, drip free dispensing system. Valve cannot be removed without taking hex nut off....
-
Safepath EZ Edge™ Transition
If you need assistance acquiring these measurements, contact our full service design team and they will find the best solution that fits your specifications....
-
Contact Information
4731 (voice) TTY: use relay service Website www.dol.gov/vets/programs/userra/main.htm For persons with disabilities, this publication is available in large print, Braille, audio tape...
-
M301.4.1 Clearance in Base (Section-by-Section Analysis)
The MDE NPRM proposed a clearance in the base of 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
Visual Acuity
Well, visual acuity is just a measure of the limit of your vision resolution (slide 7). And this is what is called the ETDRS chart (slides 7 and 8)....
-
4.5 Maneuvering Clearances
The differences between the UDI findings and the other studies suggest great differences in their protocol or measurement technique....
-
5.1 Overview of Legal Obligations
Tests must reflect the skills and aptitudes of an individual rather than impaired sensory, manual, or speaking skills, unless those are job-related skills the test is designed to measure...
