., concrete, brick, flagstone) serving primary entry doors and required exit doors are limited to not more than 1/2 inch (12.7 mm) of change in height between floor surfaces....
Search Results "Table Height"
Filters
Commonly Searched Documents
-
11B-809.8 Doors
-
Stroke Thickness: ADA Standard Section 703.5.7
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 30 percent maximum of the height of the character....
-
11B-703.8.7 Character spacing
Low resolution VMS character spacing shall comply with the pixel count for character spacing in Table 11B-703.8.5....
-
Doorways without Doors or Gates, Sliding Doors, and Folding Doors: ADA Standard Section 404.2.4.2
Section 404.2.4.2 covers the current ADA Standards for maneuvering clearances at doorways without doors or gates, sliding doors, and folding doors.
-
11B-404.2.4.2 Doorways without doors or gates, sliding doors, and folding doors
Doorways less than 36 inches (914 mm) wide without doors or gates, sliding doors, or folding doors shall have maneuvering clearances complying with Table 11B-404.2.4.2....
-
11B-809.9.5 Lower shelving
Lower shelving and/or drawer space shall be provided at a height of 48 inches (1219 mm) maximum above the finish floor....
-
General [5.1]/ Access Aisles [5.3]
The required clear width (36 inches minimum) is specified for the clearance between the edges of fixed tables or between table edges and walls....
-
1132A.3 Width and height of interior doors and secondary exterior doors
Doors shall comply with the following:
-
Pictogram Field: ADA Standard Section 703.6.1
Pictograms shall have a field height of 6 inches (150 mm) minimum. Characters and braille shall not be located in the pictogram field....
-
4.3.4 Knee and Toe Clearances
.), but the combined knee and toe clearance depth required for an individual to bring their torso to the edge of a table or counter is not specified....
-
Receivers: ADA Standard Section 219.3
Section 219.3 covers scoping requirements in the current ADA Standards for receivers for assistive listening systems.
-
11B-235.2 Boat slips
Boat slips complying with Section 11B-1003.3.1 shall be provided in accordance with Table 11B-235.2....
-
4.1.3(17)(a)
public pay telephones, public closed circuit telephones, or other public telephones are provided, then they shall comply with 4.31.2 through 4.31.8 to the extent required by the following table...
-
11B-705.1.1.1 Dome size
warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and 0.47 inch (11.9 mm) maximum, and a height...
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? The...
-
SCOPING SCENARIOS: RANGE OF POSSIBILITIES
If the market adoption rate of adjustable tables were to match a requirement that one table of every five tables meet a 19 inch lower adjustable range when facility construction occurs,...
-
Slope: ADA Standard Section 405.2
Section 405.2 covers the current ADA Standards for slope requirements on ramps.
-
Swimming Pools, Wading Pools & Spas
Word Fillable Form (2.8MB) Word Non-Fillable Form (2.6MB) PDF Non-Fillable Form (1.0MB)
-
Diversified Woodcrafts - Forward Vision & Brad (Teacher Series) Promotional Video
Brad, a science teacher shares his thoughts on the Diversified Woodcrafts Forward Vision table....
-
8.4 Improving Data Sources and Research
These data are critical for determining optimal height ranges for an adjustable breast platform....
-
Keypads: ADA Standard Section 407.4.7.2
Section 407.4.7.2 covers the current ADA Standards for designations and indicators on elevator keypads.
-
BS8300:2001 Research
BS8300:2001 Research Annex D and E to the BS8300:2001 Standard includes informative charts and tables from the results of research commissioned to obtain information on anthropometry...
-
11B-411.2.1.2.3 Accessibility function button
The International Symbol of Accessibility shall comply with Section 11B-703.7.2.1, and shall be 5/8 inch (15.9 mm) minimum in height. The indication shall be three raised dots....
