Are the surfaces of all elements of the parking area and accessible route smooth and free of large cracks and broken or raised areas?...
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
Question 2
-
Tiles
TIL was the most expensive of the five types of surfaces identified for study. ...
-
Temporary Solutions for Election Day
Problem Two: The accessible route crosses a curb and no curb ramp is provided. Suggestion: Install a portable ramp with edge protection....
-
T205.1 General
Non-rail vehicles shall provide illumination complying with T503 at ramps, bridgeplates, doorways, and boarding and alighting areas....
-
DSA Drawing 11B-406-2C Curb Ramp Adjoining a Parking Access Aisle with No Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
DSA Drawing 11B-406-6C Curb Ramp Adjoining a Parking Access Aisle with No Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
Improved Engineered Wood Fiber (EWF) Surfaces for Accessible Playgrounds Field Performance Testing: Final Report II
Improved Engineered Wood Fiber (EWF) Surfaces for Accessible Playgrounds Field Performance Testing: Final Report II Field Performance Testing March, 2002 – January, 2003 USDA...
-
Cross Slope (R302.6) (Section-by-Section Analysis)
In exterior environments, a maximum cross slope of 2 percent is generally accepted as adequate to allow water to drain off paved walking surfaces....
-
Parking Lots
Ensure that curb cuts for ramps are located appropriately—beside, not IN the parking space....
-
Wooster Products Anti-Slip Safety Coatings Systems
bare materials such as wood, metal, asphalt, marble, concrete, stone, and many other surfaces: Safe-Stride® will provide a durable and long wearing safety surface....
-
11B-406.5.10 Diagonal curb ramps
Diagonal or corner type curb ramps with returned curbs or other well-defined edges shall have the edges parallel to the direction of pedestrian flow....
-
Q1.) When a ramp has a maximum slope of 1:12 or 8.33%, is that considered a range of from 0% to 8.33% which would allow no slope greater than 8.33% or is that a simple maximum which would allow a tolerance above 8.33%? Similarly, is a cabinet countertop that can be no higher than 34” AFF a range of from 0” to 34” AFF with no additional height allowed, or is a tolerance allowed for variations in the floor surface or cabinet construction?
A1.) The consistent technical assistance on this question has been that both are subject to tolerances.
-
§ 38.83(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridges plates stowed in the passenger...
-
11B-406.5.10 Diagonal curb ramps
Diagonal or corner type curb ramps with returned curbs or other well-defined edges shall have the edges parallel to the direction of pedestrian flow....
-
3.3 Guidance on the Visual Properties of Detectable Warnings
However, low contrast detectable warnings might be sufficient if other methods are be used to increase the visibility of the curb ramp (e.g., if the entire curb ramp contrasts visually with...
-
Populas Vox Two-Story Adjustable Dual Surface Workstation Demo Video
View Product Demo
-
Are accessible spaces required in temporary parking lots and in unpaved lots, such as gravel or grass lots?
In all parking facilities, including gravel or grass lots, parking spaces and access aisles must be marked and have firm, stable, and slip resistant surfaces as specified for accessible...
-
1008.2.6 Ground Surfaces
1008.2.6 Ground Surfaces. Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with 1008.2.6. Advisory 1008.2.6 Ground Surfaces....
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where the turning space has two entrance/exit points other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep at both entrance/ exit points, as measured...
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
Inpro Corporation JointMaster® 300 Series Recessed Mount Floor Expansion Joint Covers
The patented "no-bump" design makes this product ADA compliant. Features & Benefits Patented "no-bump" configuration ADA compliant Gasketed to...
-
Inpro Corporation JointMaster® 787 Series Floor Expansion Joint Covers
The integral, high durometer seal of the 787 deters water from entering the system and acts as a noise dampening device. Features & Benefits Seismic capable system...
-
Inpro Corporation JointMaster® 101 Series Floor Expansion Joint Covers
The 101 Series is adaptable to many flooring finishes, including ceramic tile, marble, stone, vinyl, tile and carpet. Features & Benefits: Dual durometer seal...
-
Inpro Corporation JointMaster® 925 Fire Barrier System Expansion Joint Systems
The 925 Fire Barrier system meets the “Hose System Test” for masonry and concrete walls. Features & Benefits Economical system for joint widths up to 3"...
