Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
11B-902.1 General
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
f-viii
If the ramp or landing has a vertical drop-off on either side, is edge protection provided? [ADA Standards § 4.8.7] Yes No...
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
Pemko 193 Slip resistance
By slip resistance I am assuming it will meet the coefficient of friction requirement of 0.8 if installed on a ramp. Thank you -Brian...
-
Tile Tech Pavers® Oceanic™ Series - Wave-Pave™
pavers can also be manufactured with various design mixes such as crushed seashells, granite chips and recycled glass which are then honed and shot blasted for a unique and slip resistant surface...
-
902.3 Baby Changing Table Work Surface Height
-
Macro Supa-Trac Rigid Ground Cover
Requires the Premium User plan or above. (Login or upgrade your account!) -
R304.5.1 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
Resting Intervals [1018.8]
When the surface of the resting interval is constructed of asphalt, concrete, or boards, the slope of the resting interval must be no steeper than 1:48 (2 percent) in any direction....
-
Curb Ramps at Intersections
Curb ramps at marked crossings must be wholly contained within the crosswalk, excluding side flares....
-
Installation
Installation Surface materials/systems were installed by both contractors and the playground owners’ maintenance staff. ...
-
5.2.2 Transfer Surface Size Recommendations for M302
5.2.2 Transfer Surface Size Recommendations for M302 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
§ 38.95(c)(6)(ii) Exception
Ramps or bridge plates which are attached to, and deployed from, station platforms are permitted in lieu of car devices provided they meet the displacement requirements of paragraph (c)(...
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
its depth spanned the examination surface’s width, and was located near the center point of the diagnostic equipment surface....
-
Can handrails be mounted to guard rails?
Yes, handrails can be installed on guard rails if all applicable requirements are met.
-
B7-b
Is the slope (up or down the ramp) no more than 1:12? [ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for each 12 inches of length....
-
Accessible Boarding Piers
Where boarding piers are provided at boat launch ramps, sections 235.3 and 1003.3.2 of the 2010 Standards require that at least five percent (5%) of boarding piers, but at least one, must...
-
e-ii
Is the running slope (up or down the ramp) no more than 1:12?...
-
7. Commit to Ongoing Maintenance of Accessible Playground Surfaces as a Responsibility of Ownership
surfaces....
-
§ 38.95(b)(8) Platform entrance ramp
(8) Platform entrance ramp....
-
§ 38.95(c)(5) Slope
Ramps or bridge plates shall have the least slope practicable....
