The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum....
Search Results "Ramp Surface"
Commonly Searched Documents
-
405.5 Clear Width
-
Rough Form and Foundation Inspection
areas, and other site arrival points) to ensure correct accessible slopes (5% running slope and 2.08% cross slope). 11B-403 Verify forms for sidewalks, ramps...
-
Rough Form and Foundation Inspection
areas, and other site arrival points) to ensure correct accessible slopes (5% running slope and 2.08% cross slope). 11B-403 Verify forms for sidewalks, ramps...
-
503.4 Floor and Ground Surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in level are...
-
503.4 Floor and Ground Surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in level are...
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
- BORA Classic Cooktop Extraction System Installation Video
-
1. Transfer Supports
The MDE NPRM proposed requirements for transfer supports that applied to all transfer surfaces (proposed M305.2)....
-
4.1.6(1)(b)
requirements) requiring major structural changes are planned or installed where none existed previously, then a means of accessible vertical access shall be provided that complies with 4.7, Curb Ramps...
-
405.7.5 Doorways
Where doorways are located adjacent to a ramp landing, maneuvering clearances required by 404.2.4 and 404.3.2 shall be permitted to overlap the required landing area....
-
405.7.5 Doorways
Where doorways are located adjacent to a ramp landing, maneuvering clearances required by 404.2.4 and 404.3.2 shall be permitted to overlap the required landing area....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Sections 4.8.5 and 4.9.4
Section 505.3 of the 2010 Standards sets technical requirements for continuity of gripping surfaces....
-
M304.2.1 Slip Resistant
The surface on which the patient stands shall be slip resistant....
-
Transfer Surface Size – M302.2.2 Seated Position
Transfer Surface Size – M302.2.2 Seated Position The issue of seat depth was discussed and decided during the full committee meetings as follows: depth of 17 inches minimum....
-
405.7.5 Doorways
Where doorways are located adjacent to a ramp landing, maneuvering clearances required by 404.2.4 and 404.3.2 shall be permitted to overlap the required landing area....
- Inpro Corporation JointMaster® DR Series Seal Expansion Joint Systems
- SafePath: Overview of Ramps and Reducers for ADA Compliance by SafePath Products
-
A4.8.5 Handrails
The requirements for stair and ramp handrails in this guideline are for adults....
-
A4.8.5 HANDRAILS
The requirements for stair and ramp handrails in this standard are for adults....
- NanoPave® JSS 2-in-1 Joint Stabilizer and Sealer