Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
11B-604.7 Dispensers
-
407.12.3.2.2 Knee and Toe Space
Knee and toe space under ICT shall be 27 inches (685 mm) high minimum, 25 inches (635 mm) deep maximum, and 30 inches (760 mm) wide minimum and shall be clear of obstructions....
-
11B-604.8.2.2 Doors
Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum...
-
11B-604.8.2.2 Doors
Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum...
-
Omnia Industries Inc. Exterior Modern Mortise Entrance Lever Lockset with Plates - Solid Brass No.12368
Exterior Modern Mortise Entrance Lever Lockset with Plates - Solid Brass Dimensions: 10-9/16" Overall Finishes: US3*, US10B, US15, US26, US26D Notes: *Not available with square...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
1133A.4, Item 3
Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components....
-
11B-810.5.3 Platform and vehicle floor coordination
Low-level platforms shall be 8 inches (203 mm) minimum above top of rail....
-
11B-703.8.4 Character height
The uppercase letter “I” of the font shall have a minimum height complying with Table 11B-703.8.4....
-
Continuous Width (R302.3) (Section-by-Section Analysis)
, except for medians and pedestrian refuge islands where the clear width must be 1.5 meters (5 feet) minimum in order to allow for passing space....
-
504.2 Treads and Risers
Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum. Treads shall be 11 inches (280 mm) deep minimum. [ECTCR UFAS 4.9.2]...
-
1012.3 Other Vehicles
Parking spaces for vehicles, other than recreational vehicles, shall be 16 feet (4880 mm) wide minimum....
-
504.2 Treads and Risers
Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum. Treads shall be 11 inches (280 mm) deep minimum....
-
1012.3 Other Vehicles
This section requires parking spaces for vehicles, other than recreational vehicles, to be 16 feet wide minimum to accommodate vans equipped with a lift or ramp....
-
1012.3 Other Vehicles
Parking spaces for vehicles, other than recreational vehicles, shall be 16 feet (4880 mm) wide minimum....
-
11B-703.5.7 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 10 percent minimum and 20 percent maximum of the height of the character. [2010 ADAS] 703.5.7 Stroke Thickness....
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum....
-
1017.4.1 Size
A space 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum; or 2....
-
Side Entry Openings, and Width and Length of Wheelchair Space
For example, an opening of 32 inches, combined with a 30-by-48-inch minimum wheelchair space, is not enough space for turning to face the front of the ride vehicle....
-
1009.4.5 Grab Bars
The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls....
-
406.6 Diagonal Curb Ramps
The bottom of diagonal curb ramps shall have a clear space 48 inches (1220 mm) minimum outside active traffic lanes of the roadway....
-
11B-610.3.2 L-shaped seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
