surfaces. ...
Search Results "Ground Surface"
-
Play areas. (Section-by-Section Analysis)
-
505.1 General
Handrails provided along walking surfaces complying with 403, required at ramps complying with 405, and required at stairs complying with 504 shall comply with 505....
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-3 Anchor Kit (Anchor Straps)....
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-5 Anchor Kit (Anchor Straps)....
-
1.1.4 Walk cross slope
Measure for overall cross slope (the direction perpendicular to the running slope) by establishing elevations at the outside edges of the walking surface at 10 ft (3 m) intervals beginning...
-
609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
UltraPlay Getting Started Installation Video
Learn how to get started and prepare for the installation of your UltraPlay playground structure with this first of several installation videos.
-
11B-609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
2. Standing Supports
For horizontal standing supports, the Access Board proposed a gripping surface of 4 inches long minimum, the top of which would be required to be located 34 inches minimum and 38 inches...
-
Check-Out Aisles [7.3]
Writing surfaces must be 36 inches maximum from the floor....
-
Clear Floor or Ground Space: ADA Standard Section 903.2
Clear floor or ground space complying with 305 shall be provided and shall be positioned at the end of the bench seat and parallel to the short axis of the bench....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
The Brewer Company, LLC
Company, LLC Minority Report The Brewer Company, LLC 01-Oct-2013 Final Report Medical Diagnostic Equipment Accessibility Standards Advisory Committee Section 5.1.3 Transfer Surface...
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
Clearances Around Gripping Surfaces
Guidelines specify the following clearances around grab bars to ensure sufficient space for a person to grasp the grab bar: 1½ inches absolute clearance between grab bars and the adjacent wall surfaces...
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
§ 38.125(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings. ...
-
1133A.4.1 Exceptions
Two 15-inch (381 mm) wide minimum breadboards may be provided in lieu of the required 30 inches (762 mm) of countertop work surface, and used without meeting the repositioning requirements...
-
1017.6 Openings
This section requires openings in the surface of trails, passing spaces, and resting intervals such as spaces between the boards in a boardwalk to not allow passage of a sphere more than...
