Characters shall be 3/16 inch (4.8 mm) high minimum based on the uppercase letter "I"....
Search Results "Clearance in Base"
-
Characters: ADA Standard Section 707.7.2
-
Pilot Rock WPTS Square Frame Table Using Recycled Plastic
Model WPTS 8 ft table offers clearances under the table top of 30" wide, 27" high, and 24" total knee and toe clearance (19" knee + 5" toe). Nominal seat height is 18". ...
-
Pilot Rock WPTS Square Frame Table Using Lumber
Model WPTS 8 ft table offers clearances under the table top of 30" wide, 27" high, and 24" total knee and toe clearance (19" knee + 5" toe). Nominal seat height is 18". ...
-
Must the minimum number of spaces be determined separately for each parking facility on a site or can it be based on the collective total of spaces provided on a site?
The minimum number of accessible parking spaces, including van accessible spaces, must be calculated separately for each parking facility on a site. Spaces required for one parking...
-
PEMKO 8" Heavy Duty Threshold No. 1718
Eco-V thresholds are manufactured using a bio-based, phthalate-free material with no heavy metals....
-
AD Systems’ Patient Restrooms
Often, a 40” or greater clear opening is desired but having such a large door swing into a patient restroom can be very unwieldy and make other ADA clearances extremely difficult to maintain...
-
PEMKO 7" Heavy Duty Threshold No. 1717
Eco-V thresholds are manufactured using a bio-based, phthalate-free material with no heavy metals....
-
PEMKO 9" Heavy Duty Threshold No. 1719
Eco-V thresholds are manufactured using a bio-based, phthalate-free material with no heavy metals....
-
Keypads: ADA Standard Section 407.4.7.2
Section 407.4.7.2 covers the current ADA Standards for designations and indicators on elevator keypads.
-
Floor and Ground Surfaces
apply to: interior and exterior accessible routes, including walking surfaces, ramps, elevators, and lifts stairways that are part of a means of egress required clearances...
-
R210.3 Shared Use Paths
The AASHTO Guide recommends 10 feet vertical clearance along shared use paths, and 8 feet minimum vertical clearance in constrained areas....
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
TTY
Machinery that employs interactive text-based communication through the transmission of coded signals across the telephone network....
-
Envirobond is Self-Healing
If cracking or movement occurs, rain water reactivates the plant-based glue, Organic-Lock™, allowing the joint material to re-mould and fill any cracks....
-
F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes
Federal agencies shall document the basis for not fully complying with a specific provision in 1017 or 1018 on a portion of a trail or beach access route based on Exception 1 in 1017.1 or...
-
F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes
Federal agencies shall document the basis for not fully complying with a specific provision in 1017 or 1018 on a portion of a trail or beach access route based on Exception 1 in 1017 or...
-
705.1.1 Dome Size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
20. DESIGN AND CONSTRUCTION STANDARDS
In addition, HWI will, no later than one year after the Consent Decree Date, submit to the United States for review and approval a web-based design guide that identifies the ADA Standards...
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-603.2.2 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
-
603.2.2 Overlap
Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap....
