Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
Search Results "Clearance in Base"
Filters
Commonly Searched Documents
-
705.1.2 Dome Spacing
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
SmartCells Flooring: Softer Anti-Fatigue Mats are NOT Better
SATECHinc.com/media/softer Many anti fatigue mats on the market today are based off of the assumption that softer is better....
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
American Standard Jocelyn 1-Handle Kitchen Faucet 9316.000
Features include a long swivel spout for extra reach and clearance, memory position valving that provides water at your preferred temperature and an ADA-approved lever handle....
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
Dumpster Enclosures
Dumpster Enclosures Dumpster enclosures used exclusively by employees shall be considered employee work areas based on TAS 201.1; therefore, they must comply with TAS 203.9....
-
Technical Memorandum TM 2013-15 Baby Changing Tables
TM 2013-15 Baby Changing Tables Effective Date: June 1, 2013 2012 TAS Reference: 902 Baby changing tables are work surfaces based on Advisory 902.1; therefore, if fixed...
-
Hager Companies Rectangular Wrought Door Pull 2
Rectangular Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
Forward Approach
Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
-
UNREASONABLE HARDSHIP
[DSA-AC] When the enforcing agency finds that compliance with the building standard would make the specific work of the project affected by the building standard infeasible, based on an...
-
11B-403.5.3 Passing spaces
a space 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum; or, an intersection of two walking surfaces providing a T-shaped space complying with Section 11B-304.3.2 where the base...
-
11B-1009.2 Pool lifts
Pool lift seats that consist of materials that resist corrosion and provide a firm base to transfer will be usable by a wider range of people with disabilities....
-
Hager Companies Modified Half Round Wrought Door Pull 1
Modified Half Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
4.3.5.2 180-degree turn
4.3.5.2 180-degree turn Currently, the ADA-ABA does not have a specific clearance for this type of turn. The 1525 mm (60 in.) turning space would be used instead....
-
Just Manufacturing Ledgemount Swivel Gooseneck Mixing Faucet
Swiveling gooseneck spout with 7-3/8" clearance. Replaceable seats. Brass quarter turn quick compression stem units. Replaceable reinforced nitrile rubber packing....
-
Pilot Rock WUT and WUTH Picnic Table Using Recycled Plastic
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
