shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides with a full opening width...
Search Results "Stroke Width"
-
11B-608.2.2 Standard roll-in type shower compartments
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Living Earth Crafts Essex™ Pedicure Chair
options Relaxor heat and massage Wide variety of upholstery and trim color options Power drain pump Pedicure Dimensions Height - 46" (119 cm) Width...
-
Sargent HC 8800 Rim Exit Device
The HC8800 device is designed for standard width stile applications on metal doors. The Hurricane Code Hardware has been accepted by Dade County, Florida....
-
American Safety Tread Co., Inc. Type G500R Stairway Nosing Replacement
Width: 9" Lip: 1-3/8" at 90° angle Thickness: 1/4" Anchor Options: Drilled for screws....
-
American Safety Tread Co., Inc. Type SG4702 Stairway Nosing Replacement
Width: 5" Lip: 1-3/8" at 83° angle Thickness: 1/4" Anchor Options: Drilled for screws....
-
Takeform Fusion Signage Overheads Type C
Choose from 44" and 88" width, wall mount, flush ceiling mount, or suspended; ceiling mount and suspended overheads are double-sided....
-
American Safety Tread Co., Type G505R Stairway Nosing/Tread Replacement
Width: 11" Lip: 1-3/8" at 90° angle Thickness: 1/4" Anchor Options: Drilled for screws. ...
-
GE® 30" Free-Standing Electric Range JB450RFSS
Oven Features 4-Pass Bake Element 6-Pass Broil Element Oven Rack Features 2 Oven Racks 6 Rack Positions Storage Drawer Features Removable Full-Width...
-
Clarification on Standard Roll-In Shower Compliance
shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides with a full opening width...
-
1002.4.4.2 Side Entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
11B-1002.4.4.2 Side entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
Submerged Depth
Landings must be a minimum of 36 inches in width and 60 inches in length. The sloped entry may be a maximum of 30 feet at 1:12 (8.33%) slope before an intermediate landing is required....
-
1002.4.4.2 Side Entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
5.3.3 Transfer Sides Recommendations for M302
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
1002.4.4.2 Side Entry
A 32 inch (815 mm) clear opening will not provide sufficient width when entered through a turn into an amusement ride....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Edge Protection
Recommendation: At narrow routes in particular, consider maintenance of adjacent surfaces as raised or flush or wider route widths in consideration of minimum maneuvering and passage requirements...
-
Rough Form and Foundation Inspection
slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor spaces are correctly installed so proper slopes, cross slopes, widths...
-
Floor Plan of Elevator Cars [4.10.9]
In alterations, smaller car sizes (minimum 47 inch width and 69 inch length) are permitted in cases of technical infeasibility, including where limited by existing shaft configurations (...
-
Shape and Diameter
A gripping surface width between 1¼ to 1½ inches diameter is specified....
-
Rough Form and Foundation Inspection
slope). 11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor spaces are correctly installed so proper slopes, cross slopes, widths...
-
4.34.6.7* OVENS
For side-opening ovens, the door latch side shall be next to the open counter space, and there shall be a pull-out shelf under the oven extending the full width of the oven and pulling out...
