., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
Search Results "Mitigating Measures"
-
11B-707.4 Privacy
-
§ 38.175(a)
All doorways shall have, when the door is open, at least 2 footcandles of illumination measured on the door threshold....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
F105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
-
A. Accessible Voting Program
The Board agrees that the following temporary measures will be implemented where necessary to make an otherwise inaccessible polling place temporarily accessible during the voting period...
-
§1607.5 General standards for validity studies.
Evidence of the validity of a test or other selection procedure through a construct validity study should consist of data showing that the procedure measures the degree to which candidates...
-
1019.1 General
(42 U.S.C. 4332; 40 CFR 1505.2); • Agreements executed or decisions issued by a federal agency pursuant to National Historic Preservation Act stating how it will avoid, minimize, or mitigate...
-
7.1 Basic Understanding of Diagnostic Imaging Equipment
in the official National Formulary, or the United States Pharmacopeia, or any supplement to them, (2) intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation...
-
Qualified individual with a disability (Section-by-Section Analysis)
nature, duration, and severity of the risk; the probability that the potential injury will actually occur; and whether reasonable modifications of policies, practices, or procedures will mitigate...
-
1019.1 General
U.S.C. 4332; 40 CFR 1505.2); Agreements executed or decisions issued by a federal agency pursuant to National Historic Preservation Act stating how it will avoid, minimize, or mitigate...
-
AJW Architectural Products U133 56 oz. One-Piece Liquid Soap Dispenser - Surface Mounted
Neoprene seals and a stainless return spring will provide a pre-measured, drip free dispensing system. Valve cannot be removed without taking hex nut off....
-
Safepath EZ Edge™ Transition
If you need assistance acquiring these measurements, contact our full service design team and they will find the best solution that fits your specifications....
-
M301.4.1 Clearance in Base (Section-by-Section Analysis)
The MDE NPRM proposed a clearance in the base of 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
Visual Acuity
Well, visual acuity is just a measure of the limit of your vision resolution (slide 7). And this is what is called the ETDRS chart (slides 7 and 8)....
-
4.5 Maneuvering Clearances
The differences between the UDI findings and the other studies suggest great differences in their protocol or measurement technique....
-
5.1 Overview of Legal Obligations
Tests must reflect the skills and aptitudes of an individual rather than impaired sensory, manual, or speaking skills, unless those are job-related skills the test is designed to measure...
-
1117B.5.6
Dots shall be 1/10 inch (2.54 mm) on center in each cell with 2/10-inch (5.08 mm) space between cells, measured from the second column of dots in the first cell to the first column of dots...
-
Slope
Slope is measured from ground level at the entrance to all arrival points within 50 feet, and is considered impractical only when it exceeds 10 percent between the entrance and all these...
-
Updates and Other Pocket Guides
For ADA survey and compliance tools that will simplify your field measurement process and plan reviews, http://www.adasurveytools.com/ has a growing collection of templates and tools you...
-
Height and Clearances [4.19.2]
Knee space at least 27 inches high must be at least 8 inches deep measured from the leading edge....
-
3.3.6 Knee Clearance Height, minimum
In the case of the U.S. and Canadian standards, however, the level of accommodation drops to 80% in relation to measured knee heights among wheelchair users in their respective countries...
-
2.3.4 Analysis of Door Use Difficulty
2.3.4 Analysis of Door Use Difficulty The measurement of door use performance was designed as a quasi-experimental study that involved systematically observing and coding WhMD user performance...
