Specifications should include limits on how many local variations will be accepted and the methods by which accessible surfaces will be measured....
Search Results "Mitigating Measures"
-
1.1.6
-
Identification [§216.5, §502.6]
Signs must be at least 60” high measured to the bottom edge so that they are visible while vehicles are parked in a space....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Clarification on Standard Roll-In Shower Compliance
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
In determining these heights, project researchers measured the seat heights from underneath the buttocks at the center of the occupied seats, a spot likely to be lower than the front of...
-
Safe harbor for qualified small businesses regarding what is readily achievable. (Section-by-Section Analysis)
Advocacy groups both for individuals with disabilities and private businesses requested specific guidance on what measures were required for barrier removal. ...
-
2.1 Participant Recruitment and Sampling
Researchers at each of these sites were trained in the data collection methods and used the same measurement equipment to ensure consistency in measurement methods across sites....
-
4.3.5.3 180-degree turn around an obstacle
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
Section 36.301 Eligibility Criteria (Preamble, Section-by-Section Analysis)
§ 36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
B. Survey, Compliance and Review of Polling Place Locations
Department concludes that the Board or the ThirdParty Expert has proposed a remedial provision that does not address the violation, then the Department will recommend a temporary remedial measure...
-
Section 36.301 Eligibility Criteria (Section-By-Section Analysis and Response to Comments)
Sec.36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
Sampling Strategies
Let us now look more specifically at how many individuals should be measured, either in a pilot study or in a larger nationwide survey....
-
AJW Architectural Products U1304 Series 56 oz. Unidoor Horizontal Liquid Soap Dispenser - Recessed
Neoprene seals and a stainless return spring will provide a pre-measured, drip free dispensing system. Valve cannot be removed without taking hex nut off....
-
AJW Architectural Products U1314 34 oz. Unidoor Square Soap Dispenser - Recessed
Neoprene seals and a stainless return spring will provide a pre-measured, drip free dispensing system. Valve cannot be removed without taking hex nut off....
-
Whitehall Mfg. Ligature Resistant Toilet Top Supply On-Floor
This toilet is configured for a floor waste application measuring 10 or 12 inches from the wall. ADA Height and Replacement Toilet are also available....
-
Willoughby Industries ETW-1445-BS-HC Toilet for 45-degree Chase Wall
Fixture shall withstand loadings up to 2,000 lbs. with no measurable deflection and loadings up to 5,000 lbs. with no permanent damage....
-
Bradley Contemporary Series Recess Mounted Soap Dispenser 6437
Push-in valve dispenses measured amounts of vegetable or coconut oil liquid soaps, synthetic detergents, and antiseptic solutions with less than 5 lbs. of force. ...
-
AJW Architectural Products US130-A Series US130-A12 12" Exposed Flange, 1.5" Diameter Security Grab Bar - Configuration A
*When measuring and ordering grab bars, remember bars are sized centerline to centerline....
-
E102.1 Incorporation by Reference (Section-by-Section Analysis)
First, the cost of implementing this proposed rule can be mitigated, in part, through use of an updated product accessibility template that includes WCAG 2.0 and the other referenced standards...
-
Section 37.5 Nondiscrimination
If an entity may legitimately refuse service to someone, it may condition service to him on actions that would mitigate the problem....
-
11B-221.6 Semi-ambulant seats
i) It is located within the rear 60% of the seats provided in an auditorium; or i) It is located within the area of an auditorium in which the vertical viewing angles (as measured...
