The MDE NPRM proposed requiring standing supports on each side of the standing surface of diagnostic equipment used by patients in the standing position, and compliance with the technical...
Search Results "Trail Surface"
Filters
Commonly Searched Documents
-
M304.2.2 Standing Supports (Section-by-Section Analysis)
-
Diversified Woodcrafts - Forward Vision & Brad (Teacher Series) Promotional Video
Brad, a science teacher shares his thoughts on the Diversified Woodcrafts Forward Vision table.
-
Diversified Woodcrafts Lab Table Assembly Video
Quick & easy assembly instructions for this industry-leading table that is featured in science rooms, lab & research facilities throughout the world.
-
Teknion Journal
Designed by Chris Wright and Steve Tsai, Journal is a comprehensive wood casegoods system with a refined modern aesthetic designed to address this need. It is comprised of versatile,...
-
Diversified Woodcrafts 9010 ARM Lab Table Accessory
A perfect accessory to our industry-standard lab tables. The ARM (Adjustable Rotating Mechanism) is the perfect solutions for the challenges of universal design. With the adjustable...
-
1014.2.1.2 Floor Height
The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space.
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
Boston Center for Independent Living, Inc.
Boston Center for Independent Living, Inc. Boston Center for Independent Living, Inc. 60 Temple Place, 5th Floor, Boston, MA 02111-1324 617 338-6665 (Voice) 617 338-6662 (TTY)...
-
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes.
-
Slope [4.3.7]
Requirements in 4.3, while based on the expectation of level floors, apply equally to exterior sites. Where the running slope of an accessible route exceeds 5% it must be treated as...
-
Changes in Level [4.5.2]
Vertical changes in level up to ¼ inch are permitted without treatment along accessible routes. Changes in level ¼ to ½ inch must be beveled with a slope no greater than 1:2. Changes...
-
Den
Lamps wired to rocker wall switches Levers on all doors throughout the house FSC certified birdseye and quartersawn maple paneling Zoned heating on...
-
3.1.3.3 Cross Slope of Driveways
The cross slope of driveways shall not exceed 1:33 (3 percent). Exception. The cross slope of driveways may be no more than 1:20 (5 percent) where needed to ensure proper...
-
6.7 Slope
The slopes of beach access routes shall comply with 6.7.1 and 6.7.2
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
1014.2.1.2 Floor Height
The camp shelter floor at the entrance shall be 19 inches (485 mm) high maximum measured from the clear ground space.
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%. In the...
-
1016.8.3 Slope
Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage....
-
M302.2.4 Transfer Sides
Options to transfer from a mobility device shall be provided on two adjoining sides of transfer surfaces. ...
-
Section 4.26.2
• Section 4.26.2 of the 1991 Standards requires handrail gripping surfaces to have a diameter of 1 ¼ inches to 1 ½ inches, or to provide an equivalent gripping surface....
-
1016.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
1016.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
5.2.1 Transfer Surface Size
5.2.1 Transfer Surface Size...
