stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
Search Results "Single Occupant Structure"
Filters
Commonly Searched Documents
-
610.4 Structural Strength
-
Structural Impracticability (Preamble, Section-by-Section Analysis)
Structural Impracticability Proposed § 36.401(c) is included in the final rule with minor changes....
-
Sec.36.401(c) Exception for structural impracticability
(c) Exception for structural impracticability....
-
III-7.3120 Temporary structures
III−7.3120 Temporary structures (ADAAG §4.1.1(4)). Temporary buildings that are extensively used or are essential for public use are covered....
-
(a) Single-story dwelling units
For single-story dwelling units, the final Guidelines specify the same design specifications as presented in the proposed Option One guidelines, except that design features within the single-story...
-
11B-610.4 Structural strength
11B-610.4 Structural strength....
-
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 1A and Plan 1B
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 1A and Plan 1B 1991 Standards Plan-1A Pair: 1991 Standards with Out-Swinging...
-
Structural Impracticability (Section-By-Section Analysis and Response to Comments)
Structural Impracticability (Section-By-Section Analysis and Response to Comments) Proposed Sec.36.401(c) is included in the final rule with minor changes....
-
§104.23(c)(3)
(3) This section does not require recipients to make building alterations that have little likelihood of being accomplished without removing or altering a load-bearing structural member....
-
4.1.1(4) Temporary Structures
(4) Temporary Structures. These guidelines cover temporary buildings or facilities as well as permanent facilities....
-
11B-610.4 Structural strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
11B-610.4 Structural strength
stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting structure...
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
For the water closet clearance in single-user toilet rooms with the in-swinging door requirement (Req. #32), the expert panel determined that the primary beneficiaries would be persons who...
-
General description of monetized benefits for water closet clearance in single-user toilet rooms—in-swinging doors (Req. # 32)
For the water closet clearance in single-user toilet rooms with the in-swinging door requirement (Req. #32), the expert panel determined that the primary beneficiaries would be persons who...
-
"Alteration"
The California Building Code defines "Alteration" as: • "A change, addition or modification in construction, change in occupancy or use, or structural repair to an existing building or...
-
State and Local Government Facilities: Guidance on the Revisions to 28 CFR Section 35.151
has added a new section, designated as Sec. 35.151(a)(2), to provide that full compliance with the requirements of this section is not required where an entity can demonstrate that it is structurally...
-
5.4.11 Transfer Support Structural Strength for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.11 Transfer Support Structural Strength for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
§ 35.151(a)(2) Exception for structural impracticability
(2) Exception for structural impracticability....
-
§100.305(d)
(d) Newly constructed housing for first occupancy after March 12, 1989 need not comply with the requirements of this section until at least 25 percent of the units are occupied....
-
1018.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall be not less than that required for corridors by...
-
1017.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall not be less than 36 inches (914 mm)....
-
1018.3 Aisles in Groups B and M
In Group B and M occupancies, the minimum clear aisle width shall be determined by Section 1005.1 for the occupant load served, but shall not be less than that required for corridors by...
-
Homemods.org
Home modification refers to converting or adapting the environment in order to make performing tasks easier, reduce accidents, and support independent living. Home modification,...
-
1018.5 Aisles in other than assembly spaces and Groups B and M
In other than rooms or spaces used for assembly purposes and Group B and M occupancies, the minimum clear aisle capacity shall be determined by Section 1005.1 for the occupant load served...