The radius of curvature at the leading edge of the tread shall be 1/2 inch (13 mm) maximum....
Search Results "Platform Edge"
-
504.5 Nosings
-
Spout Location [4.15.3]
It is important that the spout be located at the front edge. The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.125(b)(2)(i) Requirements
The lift shall deploy to all platform levels normally encountered in the operating environment....
-
11B-302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (12.7 mm) diameter except as allowed in Sections 11B-407.4.3 _|Platform to Hoistway Clearance|_,...
-
Seat Width Evaluation
The 5th percentile wheelchair users however required transfer platform width of 25 inches if there were grab bars on the platform and 27 inches without the grabs bars. ...
-
4.4.1 Overview of Mammography Accessibility Considerations
Recognizing that the movable breast platform is the main action point, recommendations define each component in relationship to the breast platform....
-
DEFINITIONS
“Content Provider” means any non-edX organization or institution that creates and/or provides content on www.edx.org, the Platform, or edX’s mobile applications....
-
Components (M303.4)
In addition to providing knee and toe clearance at the breast platform (see M303.2.4), the height of the breast platform was identified as critical to ensuring that mammography equipment...
-
504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (13 mm) maximum....
-
Handrail Clearance and Cross Section [§505.5, §505.7]
Handrails can have circular or non-circular cross-sections, but must have rounded edges. The gripping surface and adjacent surfaces must be free of abrasive or sharp elements....
-
12162(a)(4)(A)(i)(II)
(II) such passenger can exit to the platform from the car such passenger occupies, move down the platform, and enter the adjacent accessible car described in subclause (I) without the necessity...
-
Measuring Door Openings
Measure the clear door opening from the edge of the doorstop to the edge of the door (not to the door jamb)....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
NOSING
The leading edge of treads of stairs and of landings at the top of stairway flights....
-
NOSING
The leading edge of treads of stairs and of landings at the top of stairway flights....
-
Hot water heaters and knee clearance
If the hot water has sharp or abrasive edges or if the piping serving the hot water heater falls within the required knee clearance.............
-
§ 38.83(a)(2) Exception
If lifts, ramps or bridge plates meeting the requirements of this section are provided on station platforms or other stops required to be accessible, or mini-high platforms complying with...
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
M301.4.2 Clearance Around Base
The base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
Clear Floor Space: ADA Standard Section 808.3
wheelchair spaces are not required to be located within the defined area of raised jury boxes or witness stands and shall be permitted to be located outside these spaces where ramp or platform...
-
R308.1.3.1 Surfaces
The surfaces of boarding and alighting areas and boarding platforms shall comply with R302.7. Advisory R308.1.3.1 Surfaces....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....