The bubbler outlet orifice shall be located within 6 inches (152mm) of the front edge of the drinking fountain and within 36 inches (914 mm) of the floor....
Search Results "Platform Edge"
Filters
Commonly Searched Documents
-
1117B.1, Item 4
-
Exposed Pipes and Surfaces [4.19.4]
Exposed sharp or abrasive edges are prohibited....
-
General [5.1]/ Access Aisles [5.3]
The required clear width (36 inches minimum) is specified for the clearance between the edges of fixed tables or between table edges and walls....
-
§ 38.159(b)(4) Power or equipment failure
Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding any faster than 12 inches/second (305...
-
QUESTION: WHAT DOES THE RULE MEAN BY “EXISTING FREIGHT OPERATIONS?”
, and therefore, level-entry boarding is always required at such a platform....
-
BlueDAG App
Get instant access to our ADA Inspection Management Platform. BlueDAG is a complete web application and mobile app available for both iPhone and Android....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
-
302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with 303....
-
11B-504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (12.7 mm) maximum....
-
11B-504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (12.7 mm) maximum....
-
11B-504.5 Nosings
The radius of curvature at the leading edge of the tread shall be ½ inch (12.7 mm) maximum....
-
502.2 Documented Accessibility Features (Section-by-Section Analysis)
Specifically, under proposed 502.2, platform features that are defined in the platform documentation as accessibility features would be required to conform to requirements in accompanying...
-
Adjustable height/gap protocol
Adjustable height/gap protocol: From the initial setup, a gap separating the device and platform was introduced with the plywood blocks of 3.5” (8.9cm) and then the height of platform was...
-
§ 38.109 Between-car barriers
Where vehicles operate in a high-platform, level-boarding mode, and where between-car bellows are not provided, devices or systems shall be provided to prevent, deter or warn individuals...
-
1003.2.12.1 Height
Guards shall form a protective barrier not less than 42 inches (1067 mm) high, measured vertically above the leading edge of the tread, adjacent walking surface or adjacent seatboard....
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Where doorways have steps, the illumination shall be 1 foot-candle (11 lux) minimum for a distance of 3 feet (915 mm) measured beyond the outside edge of the doorway or bottom step tread...
-
1003.2.12.1 Height
Guards shall form a protective barrier not less than 42 inches (1067 mm) high, measured vertically above the leading edge of the tread, adjacent walking surface or adjacent seatboard....
-
1015.3 Height
On stairways and stepped aisles, from the line connecting the leading edges of the tread nosings. On ramps and ramped aisles, from the ramp surface at the guard....
-
Door Clear Width
Door Clear Width Open the door 90 degrees, measure from the face of the door to the edge of the door stop....
-
4.15.4 Controls
Unit controls shall be front mounted or side mounted near the front edge....
-
4.15.4 CONTROLS
Unit controls shall be front mounted or side mounted near the front edge....
-
§ 38.81(c)
(c) The doorways of vehicles not operating at lighted station platforms shall have outside lights which provide at least 1 foot-candle of illumination on the station platform or street surface...
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
