[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
Search Results "Counter Slope"
-
TRANSITION PLATE
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
405.7 Landings
Ramps that do not have level landings at changes in direction can create a compound slope that will not meet the requirements of this document....
-
§ 38.159(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway...
-
II-6.6000 Curb ramps
When streets, roads, or highways are newly built or altered, they must have ramps or sloped areas wherever there are curbs or other barriers to entry from a sidewalk or path....
-
1127B.5, Item 4
A level landing 4 feet (1219 mm) deep shall be provided at the upper end of each curb ramp over its full width to permit safe egress from the ramp surface, or the slope of the fanned or...
-
402.2 Components
Accessible routes shall consist of one or more of the following components: walking surfaces with a running slope not steeper than 1:20, doorways, ramps, curb ramps excluding the flared...
-
10 - foot straightedge method
The same problem exists when measuring slope. There is no way to measure a localized slope that may actually be greater than the overall slope of the straightedge....
-
11B-505.10.3 Bottom extension at stairs
At the bottom of a stair flight, handrails shall extend at the slope of the stair flight for a horizontal distance equal to one tread depth beyond the last riser nosing....
-
RAMP
A walking surface in an accessible space that has a running slope greater than 1:20....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
11B-810.2.3 Connection
boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped...
-
11B-810.2.3 Connection
boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped...
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
9.a [§ 4.7.5]
To answer this question you need to determine the slope of the flared sides to make sure it is 10 percent or less....
-
405.7 Landings
Ramps that do not have level landings at changes in direction can create a compound slope that will not meet the requirements of this document....
-
Roll-in Access [1014.2.2]
To provide roll-in access into a camp shelter, a level or sloped entry route that complies with the technical requirements for an ORAR or trail, as applicable, must be provided along the...
-
11B-405.7 Landings
Ramps that do not have level landings at changes in direction can create a compound slope that will not meet the requirements of this document....
-
11B-405.7 Landings
Ramps that do not have level landings at changes in direction can create a compound slope that will not meet the requirements of this chapter....
-
226 Dining Surfaces and Work Surfaces
surfaces covered do not include those surfaces used by employees, since elements of work stations are not required to comply with these guidelines (226.1) exempt sales and service counters...
-
D. Reach Range
[ADA Stds. 5.5] Yes __ No __ N/A __ Comments: ________________________________________ ...operational controls higher than 46" if they are set back 10"-24" from the edge of the counter...
-
Single-User Toilet Rooms: No Side Transfer Space
Lavatory placement is limited by the rear gab bar, which should not overlap counter surfaces....