The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum....
Search Results "Maximum Reach Depth"
-
11B-407.4.8.2.3 Frequency
-
Section 36.406(f)(1)
In some cases, the accessible route may not be the same route that other individuals use to reach their seats....
-
Section 35.151(g)(1)
In some cases, the accessible route may not be the same route that other individuals use to reach their seats....
-
SAFE HARBOR
The 2010 Standards require paper towel dispensers to be a maximum of 48 inches from the floor. Are they out of compliance? No....
-
When Ramps Are Required
For example, to reach a 12-inch high deck or platform, a designer could use a 12-foot ramp with the maximum 1:12 slope, or a 14-foot ramp with a less-steep 1:14 slope....
-
AN INCREASING NUMBER OF HEALTH CARE PROVIDERS ARE TRANSITIONING TO ADJUSTABLE HEIGHT TABLES
While manufacturers of tables and chairs understand that lower heights may be desirable, there currently are no commercially available examination tables or chairs that can reach a height...
-
Spout Height: ADA Standard Section 602.4
Section 602.4 covers the current ADA Standards for the spout height of drinking fountains.
-
11B-602.4 Spout height
Spout outlets shall be 36 inches (914 mm) maximum above the finish floor or ground....
-
11B-602.4 Spout height
Spout outlets shall be 36 inches (914 mm) maximum above the finish floor or ground....
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
1005.2.1.1 Dispersion
Different fishing locations may provide varying water depths, shade (at certain times of the day), vegetation, and proximity to the shoreline or bank....
-
406.8 Detectable Warnings
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
-
M301.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
11B-608.5.3 Alternate roll-in type shower compartments
shower compartments, the controls, faucets, and shower spray unit shall be located on the side wall of the compartment adjacent to the 16 inches (406 mm) minimum and 27 inches (686 mm) maximum...
-
11B-608.5.3 Alternate roll-in type shower compartments
shower compartments, the controls, faucets, and shower spray unit shall be located on the side wall of the compartment adjacent to the 16 inches (406 mm) minimum and 27 inches (686 mm) maximum...
-
5.2.1.1 Transfer Surface Width Recommendations for M301
Environmental Access at the University of Buffalo, gave a presentation on the Wheeled Mobility Anthropometry Project (AWM Project).GG He provided a brief analysis of measurements of the width and depth...
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Elevator Operable Parts
These controls should be held to the basic reach range specifications in section 308 like any other operable part, according to commenters. Response....
-
Maintaining Accessibility in Museum Shops
Staff should know how to assist people who need help in reaching or seeing merchandise....
-
Kompan, Inc. Miram GXY926
Most, however, haven’t reached that level. For them, the Miram’s dual skate track system brings the excitement of action sports to the playground....
-
Accessible Routes: ADA Standard Section 1007.2
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3....
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
