The minimum clear floor or ground space required to accommodate a single, stationary wheelchair and occupant is 30 in by 48 in (760 mm by 1220 mm) (see Fig. 4(a))....
Search Results "Ground Surface"
-
4.2.4.1 Size and Approach
-
305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element....
-
11B-305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element....
-
A5.1 General
Dining counters (where there is no service) are typically found in small carry-out restaurants, bakeries, or coffee shops and may only be a narrow eating surface attached to a wall....
-
305.5 Position
Unless otherwise specified, clear floor or ground space shall be positioned for either forward or parallel approach to an element. ...
-
Section C: Exterior Route
(§303) C3 Is the route free of surface openings greater than 1/2", such as grates or holes in the pavement?...
-
Section 2. Covered multifamily dwellings
dwellings" or "covered multifamily dwellings subject to the Fair Housing Amendments" means buildings consisting of four or more dwelling units if such buildings have one or more elevators; and ground...
-
4.2.4.1 SIZE AND APPROACH
The minimum clear floor or ground space required to accommodate a single, stationary wheelchair occupant is 30 in by 48 in (760 mm by 1220 mm) (see Fig. 4(a))....
-
Pilot Rock UT Series Side Accessible Picnic Table Using Aluminum
Brace positioning allows wheelchair spaces to meet current ADA clearance guidelines of 30" wide, 27" under table (ground to bottom of table top), and 24" total knee and toe clearances (19...
-
1015.3 Viewing Space
Each distinct viewing location shall provide a viewing space adjacent to the clear ground space required by 1015.2 through which the point of interest is viewable....
-
1015.3 Viewing Space
Each distinct viewing location shall provide a viewing space adjacent to the clear ground space required by 1015.2 through which the point of interest is viewable....
-
1.5 Materials
The four simulated sidewalk sections were constructed on low wooden platforms; each covered a 1.22 m (4 ft) wide x 2.44 m (8 ft) long level area on the ground....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
904.2 Approach
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.8 Transfer Support Gripping Surface Hazard for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Kitchen Counters, Walls, and Floors
Light colored counters and floors throughout to increase reflected light and save energy. Low glare on all floors to prevent veiling reflections which are perceived as...
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
Exterior Routes
EXTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground...
-
11B-904.2 Approach
All portions of counters required to comply with Section 11B-904 shall be located adjacent to a walking surface complying with Section 11B-403....
-
11B-904.2 Approach
All portions of counters required to comply with Section 11B-904 shall be located adjacent to a walking surface complying with Section 11B-403....
-
11B-904.2 Approach
All portions of counters required to comply with Section 11B-904 shall be located adjacent to a walking surface complying with Section 11B-403. Advisory 11B-904.2 Approach....
-
Transfer Surface Height (M301.2.1 and M302.2.1)
surface....
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....
