703.1, 11B-703.2 _|Raised Characters|_, 11B-703.3 _|Braille|_ and 11B-703.5 _|Visual Characters|_ shall be located at the landing of each floor level, placed adjacent to the door on the latch...
Search Results "Self-Latching Device"
-
11B-504.8 Floor identification
-
11B-504.8 Floor identification
703.1, 11B-703.2 _|Raised Characters|_, 11B-703.3 _|Braille|_ and 11B-703.5 _|Visual Characters|_ shall be located at the landing of each floor level, placed adjacent to the door on the latch...
-
1023.9 Stairway identification signs
and braille floor identification signs that comply with Chapter 11A, Section 1143A or Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch...
-
Chapter 4: Hardware (Section-by-Section Analysis)
While each agency has different regulatory authority, self-service transaction machines can be found in a variety of settings, and the accessibility barriers are generally common across...
-
§ 37.3 Bus
Bus means any of several types of self-propelled vehicles, generally rubber-tired, intended for use on city streets, highways, and busways, including but not limited to minibuses, forty-...
-
CRL Push Button Center Locks for Glass Doors 08 4210
A variety of pull handles and latch-operating devices (Thumbturns, Keyed Cylinders, Lever Handles, and Paddle Handles) are available to accommodate different requirements....
-
§100.145(a)(3)
(3) Fails or is unable to produce self-test records or information needed to determine whether the privilege applies....
-
§100.145(a)
(a) The self-test report or results are not privileged under this subpart if the lender or person with lawful access to the report or results:...
-
Standard Stall
Stalls should be located and configured to allow forward or latch-side approaches which provide easier wheelchair access than hinge-side approaches....
-
Clear Width: ADA Standard Section 404.2.3
Section 404.2.3 covers the current ADA Standards for clear width at manual doors, doorways and manual gates that are part of an accessible route.
-
11B-404.2.3 Clear width
Exceptions: In alterations, a projection of 5/8 inch (15.9 mm) maximum into the required clear width shall be permitted for the latch side stop....
-
11B-404.2.3 Clear width
Exceptions: In alterations, a projection of 5/8 inch (15.9 mm) maximum into the required clear width shall be permitted for the latch side stop....
-
11B-809.8.3 Door maneuvering clearance.
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance....
-
Problem Four (Entrance)
Problem Four: The entrance door has a door knob and/or latch that requires tight pinching and twisting and is not accessible....
-
4.1.6(4)(d)
(i) Where existing elements prohibit strict compliance with the clearance requirements of 4.13.5, a projection of 5/8 in (16 mm) maximum will be permitted for the latch side door stop....
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
This ligature resistant cylindrical latch set meets ADA standards by eliminating the operational requirement "pinch and grasp motion". ...
-
11B-904.6 Security glazing
Telephone handset devices, if provided, shall comply with Section 11B-704.3. Advisory 904.6 Security glazing....
-
11B-904.6 Security glazing
Telephone handset devices, if provided, shall comply with Section 11B-704.3. Advisory 904.6 Security glazing....
-
Chapter 1 GENERAL INFORMATION
Self Self with device Self with assistance Assistance (What kind of assistance might I need?)...
-
ELECTRIC VEHICLE (EV) CONNECTOR
A device that, when electrically coupled (conductive or inductive) to an electric vehicle inlet, establishes an electrical connection to the electric vehicle for the purpose of power transfer...
-
ELECTRIC VEHICLE (EV) CONNECTOR
A device that, when electrically coupled (conductive or inductive) to an electric vehicle inlet, establishes an electrical connection to the electric vehicle for the purpose of power transfer...
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
