Is the lavatory (wash basin) in each accessible guestroom bathroom no more than 34" high with at least 29" high clearance under the front edge to allow persons who use wheelchairs to pull...
Search Results "Clearance"
Filters
Commonly Searched Documents
-
7. Lavatory
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
D. Beds in accessible guest rooms and sleeping rooms
Many individuals with disabilities have urged the Department to regulate the height of beds, particularly in accessible hotel guest rooms, and to require that such beds have clearance under...
-
Shower and Sauna Doors in Transient Lodging Facilities
The exemption to the section 224.1.2 requirement for a 32-inch wide clearance at doors to shower and saunas applies only to those showers and saunas in guest rooms which are not required...
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Bobrick ConturaSeries Surface-Mounted Seat-Cover Dispenser B-4221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
Bobrick Recessed Paper Towel Dispenser B-318
Rough Wall Opening: 12" W, 18 1⁄4" H (305 x 465mm) to accept cabinet height, plus 6" (150mm) min. clearance space below towel tray; 4 1⁄2" (115mm) min. depth....
-
F204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance...
-
204.1 General
Within play areas, protruding objects on circulation paths shall not be required to comply with 307 provided that ground level accessible routes provide vertical clearance in compliance...
-
4.1.6(3)(c)(iii)
For example, an elevator of 47 in by 69 in (1195 mm by 1755 mm) with a door opening on the narrow dimension, could accommodate the standard wheelchair clearances shown in Figure 4....
-
4.2.6* Side Reach
If the side reach is over an obstruction, the reach and clearances shall be as shown in Fig 6(c)....
-
4.18.3 Clear Floor Space
Urinal shields that do not extend beyond the front edge of the urinal rim may be provided with 29 in (735 mm) clearance between them....
-
4.1.6(4)(d)
(i) Where existing elements prohibit strict compliance with the clearance requirements of 4.13.5, a projection of 5/8 in (16 mm) maximum will be permitted for the latch side door stop....
-
4.2.5 FORWARD REACH
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b). Figure 5 Forward Reach...
-
4.18.3 CLEAR FLOOR SPACE
Urinal shields that do not extend beyond the front edge of the urinal rim may be provided with 29 in (735 mm) clearance between them....
-
§ 38.159(a)(1) General
., lift or ramp) complying with paragraph (b) or (c) of this section and sufficient clearances to permit a wheelchair or other mobility aid user to reach a securement location....
-
Murdock Manufacturing Grab Bars
Grab bar is 1-1/2 inch (3.81 cm) diameter satin finish stainless steel and have 1-1/2 inch (3.81 cm) clearance to wall....
-
4.3.9 Doorway Design
The lack of differences between the findings for the passage task on the pull sides of Doors 1, 800 mm (31.5 in.) latch clearance, and Door 2, 406 mm (16 in.) latch clearance, demonstrate...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
